Clik here to view.
Guest wireless using ERLite-3 and DD-WRT AP
Coming from years of using consumer routers, my goal has been to replace my old Tomato-based wireless router with the ERLite-3 and a wireless acess point (using an old Trendnet wireless router with...
View ArticleHelp Opening and Verifying OpenVPN tunnel to ProXPN (ER-X)
Hello, Firstly I have taken the .ovpn file from the ProXPN windows client. It is listed as shown:client dev tun ; proto udp resolv-retry infinite nobind persist-key persist-tun cipher BF-CBC keysize...
View ArticleEdgeswitch16XG 12 SFPs and 4 1gb ports
Hi There,Im setting up a mikrotik CCR with SFP 10G connection to Edgeswitch SFP 10GB. The trunk port is up. I have setup a bridge port on the mikrotik with 2 vlans with DHCP and DHCP on the bridge...
View ArticleRoute display issue with v1.9.0
Hello, I noticed after upgrading my ER-POE to v1.9.0 that my default route (which is set via PPPoE) does not appear in the Routing section of the GUI. My other routes are all there - only the default...
View ArticleHardware Refresh of EdgeRouter Lite?
Good evening, I was wondering whether there are any plans regarding a HW refresh of the EdgeRouter Lite or any other of the 'end-user' / home models in regards to their CPU performance. I am wondering...
View ArticleHelp getting OpenVPN (Client to PIA) to come up
I have used the following thread for help but it seems a bit old and im wondering if anything has changed with PIA setup or something within EdgeOS in the newer versions. Im just looking for a quick...
View ArticleClik here to view.
ERPoe5 VLAN without a Managed Switch?
Can I use the ERPoe5 switch ports to create three networks? Two wired networks with WiFi and one strictly WiFi? I have configured a UniFi AP AC Pro to broadcast three wireless networks using 3 VLANs...
View ArticleGUI will not load, displays Fatal Error Unable to load router configuration.
I just purchased and Ubiquiti EdgeRouter PoE, model number ERPoe-5. The GUI loaded for me initially, but no longer does after I attempted to upgrade the v1.2 that it came with to the current 1.9...
View ArticleOpen ports for VoIP access
Hi Folks,I have never used this product so I am a complete newbie. I am also only able to access the router remotely as I am based in Ireland and the modem is in Arizona. We hired a technical gut over...
View ArticleDUAL WAN (Failover) + Source address Policy based routing
We currently have a ER-PRo8 setup with dual WAN where the second WAN connection is used only as failover. This was setup using the wizard. We would like to add one more policy on top of this setup...
View ArticleBrand new Edgrouter Pro (ERPro‑8) Very slow WAN performance
We recently got upgraded to 1Gbps fiber (not Centurylink PPoE stuff). Our current ASA 5520 could not saturate the link, so I picked up a ERP8 to test. All I've done so far is update to FW 1.9 and run...
View ArticleClik here to view.
ER-Pro - Different hardware revisions?
I have seen some models of ER-PRO that have an older logo on the front bezel left-hand side, and others with the newer ´U´ logo. Is there a difference in the hardware that I should be aware of, or is...
View ArticleEdgemax v 1.9.0 session per user limit
Hello, is there any way how to limit active sessions per user in time?My provider gets me 1000 paralel sessions and I need to limit user in network for 100 sessions in one time. Every sessions after...
View Articlemartian destination
Apr 7 14:11:30 ADVA006 kernel: IPv4: martian destination 0.0.27.68 from 123.123.123.123, dev eth0 123.123.123.123 is one of our public ip addresses that is on the lan side. Any help would be...
View ArticleER Pro 8 - LAN to LAN routing
Hello, I have a unique office that is a shared office. Meaning there are multiple tenants that all share a common office. I installed an ER-8Pro and setup the ethernet ports as follows: E0 InternetE1...
View ArticleERL 3 upgrade from 1.8.5 to 1.9 seems to fail
I downloaded the 1.9 upgrade to the ERL 3 this morning and when I uploaded the rascal to the ERLall I get is a spinning wheel, I gave up after two hours... What am I doing wrong? jerry@ubnt:~$ df -h...
View ArticleClik here to view.
Edgerouter X, ER-X USB TTL Serial Port Mod
I love the ER-X but cant stand having a device without a serial port. So I decided to VOID MY WARRANTY and install one myself. Please Ubnt make a new revision of the device with a serialport built in!...
View ArticleSIP proxy / forwarder on ER-POE
Hello, I have a Cisco 7965 IP phone configured in SIP mode behind an ER-POE. NAT is used on the WAN side, as is typical. This phone's NAT traversal support is very poor, to the point that it can't...
View ArticleTroubleshooting VLAN over load balancing
I currently have 2 internet connections (eth0 and eth2) setup as load balancing so that when my first connection fails, the other one kicks in. This seems to work, when I turn off the modem of my main...
View ArticleER-X L2TP slow connection
I just recently purchased and setup a ER-X using a L2TP VPN server to connect several devices remotely. I was able to setup the L2TP server successfully using the following guide, but the throughput...
View Article