Powering EP-6
Background:I have a farm house where I needed to run the dish out past the trees to get a signal. I originally looked into the F-POE units. First time using them and the info on them isn't that...
View ArticleDisabled interfaces enables itself after some time
Hi, If i disable a port - let's say eth1 in the GUI - it seems that it enables itself after some time. It's still greyed out in the dashboard but i can see packets flowing in the TX/RX collumn. Is this...
View ArticleEdgeRouter PoE - Multiple WAN IPs Port Forwarding
Hey Gang, I have been running this OS as a nubie for about a year. I have learned a lot but cant seem to bust through this one. I havemultiple static WANip addresses. I want to split traffic INCOMING...
View Article1.9.0 DPI Problem
Two separate ER-X routers at different locations both have an issue with DPI after about 2 weeks of service. They start moving services (streaming/media) into web/other. A reboot will correct...
View ArticleERL Site-to-Site VPN with Barracuda NGFW - all traffic to IPsec
Hi all, I've been trying to set up an IPsec tunnel between an ERL and a Barracuda NGFW since nearly 2 weeks but can't get it to work, that all traffic from ERL site goes to the Barracuda site. My...
View ArticleLoad Balance issues
I have 3 connections from ISP on ports eth7 (Static IP), eth6 (DHCP Client) and eth5 (DHCP Clinet). Setup by wizard load balancer on the router ER-8 version 1.9 load-balance { group G { interface eth5...
View ArticleERLite - Auto Restart VPN
I'd like to request following features:A command for restarting OpenVPN clientA tool that restarts OpenVPN client if it stops working (for example, based on ping)Or they are already available?Thank you.
View ArticleNEED SOMEHELP
OK gang ... I have posted the same question a couple of times. I see where the questions have been seen by a few. I had one response that was not detailed enough for me to follow and seem to indicate I...
View ArticleClik here to view.
EdgeRouter X - Config for Split into 4 Subnets (1 per Port)
Dear All, I am quite new to all this and figured, that after 10 hours of trial and error and web-search without any working solution I might ask you Pros out there. This is for a small "home-config",...
View ArticleReplacing ERL with ER-POE5
I am replacing an ER Lite with a ER5POE - Am I able to take a backup from the ERL and restore it to the ER5? This is assuming they are both on the same release of firmware. Any issues with this? Thanks...
View ArticleInternet disconnects intermittently
I have an EdgeRouter POE5 connected to a microsoft surfboard cabel modem. Using 2 of the POE ports for UAP-AC wireless and another port going to a Cisco switch to distribute throughout our office. I...
View ArticleStrange VLAN Performance on EdgeRouter Lite 1.9
Hi everybody!Before I spew out walls of text this is the overall problem:I've got a strange performance issue that I can't pinpoint. Randomly, VLAN traffic out to the internet is very poor. Pings...
View ArticleVPN to PIA & VLAN on ERL Noob needs help :-)
HI All,I am wanting to setup a VPN to PIA on one of my Vlan's. I am running 1.9. I would like to connect one of my servers to run over the VPN, the servers are already on the Vlan. I was wondering if...
View ArticleEdgepoint R6 with S-RJ01
Hi I have been using the MikroTik S-RJ01 with the edgepoint R6 on version 1.7.X and 1.8.0 without any problem. Today i have decided to upgrade the Edgemax software to 1.9.0 and i have remarked that...
View Articleipv6 Tests Fail -- EdgeOS Firmware v1.9.0
ERL and firmware v1.9.0Cable Modem in Bridge ModeI upgraded my ERL from v1.8.5 to v1.9.0 on August 11, 2016 and since that date I have not been able to pass any ipv6 tests using the following 2 sites:...
View Articleno reverse dns in traffic analytics
Hey, I have enabled dpi on my edge router , which works fine, but all ip's aren't translated to hostnames via my dns service. I'm not using the build in dns server. I configured my dns server under...
View ArticleNewbie help on ERX - tor related
Hello, I just installed an ERX on an isolated network yesterday both to learn the EdgeMax line and to isolate one network. I have just done the standard WAN-2LAN2 wizard and added hwnat offload....
View ArticleL2TP VPN and Site-to-Site?
I feel like I'm either 1) doing this wrong or 2) thinking this wrong, please feel free to mock me as needed. I have a Site-to-Site set up, works great, no issues. With the impending PPTP drop from iOS...
View ArticleER-PoE - Chromecast between subnets, wireless client to wired host
Hi, After searching high and low, I can't get my wireless deviced be able to pickup my Sony TV. Also tried the bcast relay stuff. I run the AP-Pro on a different subnet. Were able to fix the mDNS...
View ArticleDNAT rule not working - 5 static address block from ISP
I have an ERX running 1.9. 5 static block from the cable ISP a.b.c.24/29Gateway = a.b.c.25Usable = a.b.c.26-30 I have a.b.c.27 and a.b.c.29 assigned to eth0 Internet interface. WAN_IN rule to allow...
View Article