Access a server on WAN
I have a EdgeRouter Lite running v1.9.0 firmware.I have the stock WAN + 2LAN2 config.I am trying to reach a server in the same subnet as the WAN interface.(as if the WAN was 10.0.0.1/24 and the server...
View ArticleEdgeRouter X, CenturyLink Fiber, Hairpin NAT
v1.90 Using the wizard for WAN+2LAN configured, connected to ONT from CenturyLink just fine. Using eth0, MTU 1492 and VLAN 201 (as furnished by CenturyLink), eth1 to switch all is good. Except Hairpin....
View Articleedge router and cisco TelePresence
Sorry I'm a bit new to the forum and I need some help with an odd situation. I have an edgerouter x, works perfect. But my client got a cisco TelePresence sx10. Its a video confrencing camera, very...
View Articleedgerouter lite 1.9 DHCP static MAC/ip Lease not working
So i just picked up a edgerouter lite, i upgraded to 1.9 and am about to configure DHCP to replace my MS server 2012 DHCP server, my problem is i have 2 GWs so some devices go out GW1(edgerouter) and...
View ArticleAdd WAP to X
My EdgeRouter X is assigned with my wired LAN on eth1 and on eth2 I plugged a consumer AP which is working. What do I do so my interfaces cannot access each other?
View ArticleDaisy chaning fiber switches to router?
I've got a EdgeRouter Pro and two Unifi Switches. How should I connect the 3 devices? I want them all to be connected with fiber optic cable, using the SFP ports. I see 3 possibilities Scenario 1...
View ArticleNon-routable addresses are not being blocked
I have an EdgeRouter Lite that was set up using the wizard. Firnware is v1.9.0. Eth0 is LAN. Eth1 is WAN. Eth2 is unused. Internal addresses are 172.16.0.xx/26. All addresses are manually...
View ArticlePort won't open...
I don't know why I'm struggling with this. I have an ER-Lite that I have used for over a year. I have 10 forwarded ports that correctly show open from the outside world. Tonight, I added two new ones...
View ArticleRegression in FW 1.9.0
After installing FW v1.9.0, on the Dashboard, if you scroll down to view the interfaces at the end of the list, everytime the graph updates, the list scrolls back to the top. This makes it almost...
View ArticleZone Firewall and PBR
Has anyone got any experience of using PBR with the Zone Firewall. I have a working sone firewall with INT, EXT, IPV6, and DMZ zones and want to add a OpenVPN tunnel to route traffic from a small...
View ArticleTagging untagged traffic on switch0 to a VLAN and vv
I have a scenarion where, currently, I have eth2/3/4 as part of switch0, three vifs on switch0, each with their own subnet /24. I cable from eth2 to a managed switch and use switch facilities to...
View ArticleLog entries - possible compromise
These entries began showing up in the router log. To me it appears that something is trying to phone home. Not to sure I understand the these entries completely. Your assistance please. Aug 21 11:26:49...
View ArticleLooking for a Systems integrator in or near Massachusetts
Not sure where to post this, so I am trying here and in the Video forum.I am looking for a systems integrator to design and install a Video and outdoor Wi-FI system on a 58-acre farm. I need especially...
View ArticleIPSEC IPv6 support over IPv4 possible without encapsulation?
Hello, I'm messing with IPv6 over IPSEC on ER-X and I obviously need some help...My goal is to grab a slice (/64) for my local ER-X, of /56 prefix I have on a server hosted in a datacenter. This server...
View ArticleFeature Request - Updated OpenVPN
Hey, I have another feature request for EdgeOS for ER-X and equivalent. Currently the installed version of OpenVPN on the ER-X firmware 1.9 is OpenVPN 2.3.2, which lacks specific TLS 1.2 capability, as...
View Articleedgepoint power monitoring
Hi,I've just got my hands on an edgepoint er-6, and in the documentation it mentions power monitoring for both DC and PoE inputs.I've had a look around the edgeos GUI and can't see anything that shows...
View ArticleERL on 1Gbps Fiber - Download 20mbps / Upload 1gbps
So I have been struggling with this today and am getting no where. Not exactly sure what is going on but I can not get around this issue at all. No matter what I do I always get 20Mbps down and 1Gbps...
View ArticleER-X Basic config wizard writes incorrect config when ISP uses VLAN
Hi I tried configuring my ER-X SFP for an ISP that uses VLAN tagging. So I went through the wizard, entered the correct VLAN id, and let 'er rip. After the reboot.. no WAN IP. No surprise there since...
View ArticleER-Lite vlan software based?
Hi I have an ER-Lite as a router for my Gigabit Internet connection. I configured a VLAN on eth2 (VLAN5) to have a different subnet for a work thing. While that all works just fine, when I run a speed...
View ArticleClik here to view.
EdgeSwitch to EdgeRouterX via SFP
My apologies if this has been addressed in other post. Please point me in that direction if another exists, but I could not find one. Setup: Microtik WISP > WatchGuard Router > EdgeSwitch 500W...
View Article