Clik here to view.
EdgeRouter dashboard doesn't work with Safari
The EdgeRouter Dashboard doesn't work with Safari:
View ArticleER-X Internet Not Working
Hey guys, somewhat new to ubiquiti products, but I am having an issue with my ER-X router. I downloaded the newest available firmware and installed without an issue. My problem, is that, I am unable to...
View ArticleERL becomes unresponsive after creating basic qos queues
Created 75 queues on my erl and now it will not allow me into the web interface consistently and if it does it hangs the web browser when I go to add more queues
View ArticleOwn firewall rules on VLAN-"Subport"?
Hi, I'm currently using two physical ports on my ERPro for the connection to my internal network. eth0 is the "unlimited" core network, eth1 is connected to a switch port which tags it with VLAN50 for...
View ArticleCan't get the firewall to block pings on ER-X across subnets
Been trying to segregate two separate LANs in my house, but am still getting pings across subnets.I have an ER-X, with eth0 as the WAN, eth1 as the owner IP (192.168.2.1), and eth2 as the tenant IP...
View ArticleClients not using static host mapping
Hello, I am trying to set up a simple network where the EdgeMax Router(WAN 10.218.60.11/LAN 192.168.21.1) is connected to our outisde router (10.218.0.1). I want the edgemax router and its clients to...
View ArticleMultiple ip address on same WAN interface with dhcp
Hello I'm looking into small problem. I have fiber to my house and there is a telsey endbox that I connect my ERX to. I should be able to get up to three public ip addresses through this Telsey box...
View Articlestatic public ip mapping
Hi, I'm still getting the hang of the edgemax products and I was wondering if someone would be able to help me out with my question. My company has fibre into our building so we sell a portion of the...
View ArticleSmart Queue throughput
If I am I reading this correctly, it appears that the ER-X CPU has a bit more capacity here than the ERL CPU does. Have subsequent releases changed any of this? Also, is there any hope for future...
View ArticleEdgepoint R8 Powersupply
I am looking at setting up a Edgepoint R8 on a light pole in a parking lot to aggregate cameras. I have 120vAC at the pole, the power is always on to the 120v line. I am looking for suggestions for...
View ArticleER-X upload control
Hi everyone,New Edgerouter X user, i'm looking for a way to limit upload rate to a specific remote IP adress through a specific port.For example i got a 10mbits upload bandswich, i would control the...
View ArticleERLite OSPFv3 doesn't work on 1.8.0 or later
I can't get OSPFv3 to work on 1.8.0 or later. Tried everything I can think of. The other side (a Cisco ASA 5585-X) never gets past the LOADING phase with the following config: interfaces { ethernet...
View ArticleERPro-8 issues with NAT and/or Bridging
Hi, Hope you can help me with this as I've done many atempts to solve it but oviously I haven't got into the solution yet. The situation is that currently I have an ERPro-8 in a datacenter which has...
View ArticleFailover WAN routed IP
We run a WISP that routes public IP's over our 10.0.0.0/19 network. All radios are in bridged mode and we terminate the customer with a 8 port EdgeMAX router. eth0 is connected to the 10.0.0.0/19...
View ArticleAnyone running a walled garden for suspended clients through the Edgemax?
We are looking to implement a walled garden for subscribers we wish to suspend for non payment. Our present setup has two Edgerouter ER-8's at our internet uplink points in two physical locations. So...
View ArticleLoad balance
I am using the edgeRouter POE and I did configuration for the wan+2lan at the wizards section.the WAN is at eth 1 and Lan is at switch 0 (eth2 , eth3 , eth4)Now I need to add another WAN at eth 0. In...
View ArticleBell Fibe / FibreOp
Hello All, so with some reading and other digging I've had my Fibe Gigabit(Formally FibreOp) working pretty flawlessly since April, but never ended up getting the IPTV to work... I've not bothered with...
View ArticleNeed to Send All Traffic Through vti tunnel (IPSEC VPN)
I was succesfull in creating an IPSEC VPN with vti from an EdgeRouter Lite to a paloalto firewall. I'm able to create static routes for subnets that live on my primary network, and that works fine,...
View ArticleAzure to EdgeRouterX Site-to_Site VPN not connecting
My setup:EdgeRouter LAN: 10.0.0.0/24Outside interface: eth0 Azure network: 172.16.0.0/27 The connection is attempting to establish, but I can not get it to connect properly. The error logs are at the...
View Articleegde lite 3 vlan34 (fiber) vlan4 (itv) cause to disconnect
after 30 days my router disconnect my internet and itv. after reset the settings to factory default and setting up . vlan34 (internet) works agian but after restore my config than its disconnects its...
View Article