Re: 1.8.5b2 Unable to configure IPv6 only BGP peering (ie, no IPv4 address...
new bugs: I have 2 peers, when disconnect one, new loading array BGP from 0
View ArticleWireless AP internet access issue with EdgeRouter X
I've just purchased a Ubiquiti router and got it setup on my home network. I have about 30 devices, most are wired. Everything is working ok except one thing.I have a Picostation outdoor ap which I am...
View ArticleDisplay EdgeOS Statistics in UniFi
As a big fan of the ERL, I wonder if there's any possibility to have the ERL submit data to a UniFi Controller. Just for traffic analysis and having the WAN be displayed in UniFi. I do NOT intend to...
View ArticleVPN over DMZ, 2 edgerouters HELP
I have 2 edgerouters and I am trying to connect them with a vpn Router 1 was setup using LoadBalancing wizard and Eth0= 10.10.10.173/29 (connected to bridged modem(want vpn to go through here)Eth1=...
View ArticleEdgePoint EP-R6 SFP J4858C doesn't work
Hi, i tried to connect the EP-R6 (FW 1.8.5) with the SFP Module J4858C to a HP V1910-48G but i doesn't work. The module on both sides are detected. It is a HP Original but the EdgePoint detect the...
View Articlepersistent NAT?
I just installed a Edge Lite at a customer. They use a phone system by Vertical. We have a static IP from the cable company on Eth0. Eth1 is 10.0.0.1/24 On the LAN is an Open VPN server and a phone...
View ArticleClik here to view.
VLAN on Edge Router Pro POE
Hello,I'v been banging my head on this for about a week now and i cant seem to get it to configure the vlans. here is how im trying to do the setup Cable Setupeth0 WANeth1 Core network Switch Running...
View ArticleIPSEC S2S VPN reliability
I have an IPSEC VPN between two ER-Pro's that seem erratic at best and completely broken as a realist. There are no users there currently, but we have some SIP phones and other devices I am trying to...
View ArticleConsequences when running the load balancing wizard
Hello, As EdgeMax doesn't seem to support multi WAN without load balancing I moved everything to one WAN connection which all seemed to work fine. Today I figured out that something wasn't working......
View ArticleL2TP server user specific IP
Hi, Is it posible to assign different LAN IP's (VLAN) to L2TP users? Currently we just configure one client-ip-pool which can route to the different VLANs but we want to exclude some users from that...
View ArticleIpv6 help with edgerouter lite
Need some guidance to setup IPv6. I have the router setup as one WAN (eth0) with two LAN (eth1, eth2). My provide gives me the following IPv6: YOUR IPV6 ASSIGNMENT:NETWORK ID:...
View ArticleVoIP behind NAT issue
I am having an issue where VoIP phones (Polycom VVX 400) behind my EdgeRouter are not able to answer calls when our Everyone ring group is hit. The phones ring, but neither picking up the handset nor...
View ArticleFuc... USB flash
Recently I have a lot of problems with USB flash memory in EdgeMax routers. Real pandemic. Just this week four of them died. And I know I am not the only person with this problem. Therefore I would...
View ArticleLoad balance ERX - not co-located connections.
Hi all, This one has had me scratching my head for a while. Presently I have two offices that are running off one ADSL connection. I have ubiquiti radio on the roof of both offices and a router that...
View ArticleConfigure ERLite-3 PXE boot to point to NFS server
Hello All, EDIT: Ok, just realized my mistake on, having checked the guide linked below again. I thought it was pointing to the router, not the NFS server....
View ArticleSetting up a home router with IPv6 only
I would like a streigh forward setup for an edge lite with a /64 IPv6 address for a typical home users.It would be nice if it could be done quickly without typing a book of command line code.any...
View ArticleEdgeRouter Lite 3 setup for easyDNS token
Well I've done my best google-fu and I just can't figure this out. I can see that easyDNS is one of the supported DDNS services, but I can't figure out how to enter the details in the web gui or cli...
View ArticleIPSEC Tunnel Dropping
Using IPSEC tunnels, and all of a sudden on of my tunnels goes down. I have syslog running on both the hub and the spoke locaitons. It looks like the hub location goes down first, then the spoke 1...
View ArticleEdgerouter POE and subnet access
Ok, so I am going to try to explain all of this as best as I can and hopefully someone can help. We have several networks going on Main Incoming is 10.1.10.1/24Connects to Ubiquiti router at 10.1.10.25...
View ArticleCan I get some clarification on how packets flow when QoS is involve?
I am trying to figureout why my trafic-policy shaper is not matching anything but default rule for download traffic. My only guess so far is I am applying wrong match rules and/or wrong in/out...
View Article