Clik here to view.
Firewall modify based on DPI
I'm wanting to send streaming media and social networking over ADSL, traffic from my work PC to a 4G connection, and all traffic from other hosts over ADSL. This is the config I have created. $ show...
View ArticlePassing GPS position to network clients
I have a UAP-AC Pro connected to a TS-8-PRO connected to a ERPOE-5 (which also has a Sierra Wireless GX450 connected to it, providing internet and GPS location). This is all installed in an RV...
View ArticleNAT with Fail over connection
I am trying to setup a 1:1 nat with a router that is behind an Edge Router A->B It works fine but as soon as I do the load balance wizard to setup a failover connection, then setup the nat, it will...
View ArticleHELP! Edge Router X SFP and Ubiquiti Switch 750wt 48port
Anbody that can help,I am trying to set up a new network using and Edge Router X SFP and a Ubiquiti Switch. I want to use the Edge Router to provide a low grade firewall and to provide internet to the...
View ArticleIssues with v1.8.5 NAT Hairpin
I recently purchased an edgerouter poe. I upgraded firmware out of the box and was able to transition most of my infrastructure over to the new router with little issues. I do have an issue with the...
View ArticlePort-forward to DNAT Conversion
I have the following interfaces configured: eth0 AKA WAN (dhcp address)eth1 AKA DMZeth7 AKA LAN All outbound traffic from the LAN or DMZ to the WAN is using SNAT. Currently inbound traffic to the DMZ...
View ArticleCan't get OpenDNS to work on my EdgeRouter Lite
I've tried going to the System tab, and adding 208.67.222.222 and 208.67.220.220 and clicking save, then rebooting but it doesn't work. I go to welcome.opendns.com and it says I'm not configured...
View ArticleClik here to view.
Perhaps stupid question about ER-X vs USG/ER-L
Hi! I bought both the USG and ER-X and I love both products (I also have the toughswitch and 2 AC-AP-LR).The last days I read and read and read about the differences between the ER-X and the ER-L/USG...
View ArticleUpgrade from 1.8.0 to 1.8.5 config change
Upgraded from 1.8.0 to 1.8.5 on erlite-3 earlier, no issue. Then after an Internet outage, no more IPv6 connectivity. I compared the config on 1.8.0 right before the the upgrade and after upgrade (root...
View ArticleClik here to view.
ER-X SFP bricked after attempted upgrade to 1.8.5
Dug out my ER-X-SFP to upgrade to 1.8.5 and the device has bricked itself! Following the upgrade, the device stops functioning and is not reachable on the network. Full dump of the boot process from...
View ArticleClik here to view.
IPSec with responder inside ipsec tunnel
Hello i need help with my setup ERoutside: 172.16.0.2 - nat device (172.16.0.1) - INTERNET - ASA 123.123.123.123:outside inside: 192.168.0.0/24 10.0.0.0/24:inside I have created a ipsec tunnel from...
View ArticleERX PPPOA sluggish UI & Slowness
when I connect ERX as a PPPOA client, its UI is dead slow and takes forever to respond - internet is very very slow - but when I use it otherwise (WAN DHCP - thus putting back the ISP router before the...
View Articlev1.8.5: ssh listen-address IPv6 link-local does not work
While `set service ssh listen-address global-IPv6-address` works, the similar syntax for `set service ssh listen-address link-local-IPv6-address` does not. Including variations with link-local%eth0 or...
View ArticleSites not loading or timing out
Just bought a EdgeRouter Pro 8 and it seems fine but some sites do not load correctly.Sometimes they take time to load and time out. Not sure what is wrong. I have included my config
View ArticleInternet connection dropped by 100mbps after switch from Asus to ERPOE-5
With my Asus AC1900 router, I was testing at 230 mbps on internet speed tests. Now I'm testing at 130mbps with ERPOE-5. I used the wizard and selected WAN+2LAN2. Two AP AC Pros (POE enabled) and one...
View ArticleI need to be able to log or do more troubleshooting
There are a number of paths to greaters logging that don't seem available on the edge router lite. There are recommendations to "set system syslog global facility all level debug", but the only "set...
View ArticleGetting UDP Broadcasts across subnets
Hi all, I am using VLANs to separate some LIFX lightbulbs from my main network in order to be able to use firewall rules to block access to certain bulbs from the main network (kids having control over...
View Article1.8.5 VLANs and traffic-policy shaper not working
We currently have a single customer at the base of a tower who pays for 200 Mb of internet which comes from an airFiber 24. There was absolutely no room in their rack for a switch, so we used a EP-R6...
View Articlenoip DDNS with 2 WANs
Good day all... I am using 2 WAN connections, load balanced, the DDNS update in GUI (checked the CLI, the same) is for pppoe0 only. I noticed in noip site that the IP is for pppoe1. 1. I did change the...
View ArticleProblem with UAPs informing to AWS controller
Hi! Ive just turned on the firewall on an Edgerouter-X with a number of UAPs behind it, which previously informed to the hosted AWS unifi controller with no issues, I added the standard port forward...
View Article