ER-POE5 POE concern (Possible firmware bug?)
I have an ER-POE5 that I use with an NanoLoco M2. During a firmware upgrade the M2 failed. During a cursory investigation I noticed that even though I had turned down POE and the port in the GUI that...
View ArticleStatic route not working
Hey guys so I am still new to Ubiquiti I am trying to rap my head around the following not working we have a EdgeMax PRO two ISP first one is on eth1(copper) and second eth7 (Fibre)I want to Failover...
View ArticleFollowed this guide to replace usb pen but it boots once then wont reboot again
Hey so I followed this guide using a usb3 64gig pen on my edgerouter poe https://lukas.im/2016/01/25/replace-broken-usb-stick-in-ubiquiti-edgemax-routers/index.html And it works but the pen comes up...
View Article"Bridge firewalling registered"
Below is /var/log/messages from a ER-X-SFP at a client site. It rebooted on 8/15. Then on Aug 17, the first and only msg after the boot sequence is a line with: "Bridge firewalling registered" $ cat...
View ArticleClik here to view.
Not initiating IPSEC connection attempts - ERX- EdgeOS 1.9
Hello, I'm in the process of establishing a bridge from my ERX at home to my Linux server hosted in a datacenter... Goal is to setup a gre over ipsec tunnel and play with it. Many caveats I have to...
View ArticleUPNP2 broken on 1.9.0 for ER-X SFP ?
I upgraded from 1.8.5 to 1.9.0 on my ER-X SFP. Afterwards my Plex server could not open a port in the firewall. I checked the through show upnp2 rules and nothing came up. As soon as I downgraded to...
View ArticleSimple routing question: route between 2 subnets
Hi, I own a ER PoE configured by the wizard with 1 port wan, 1 port on a subnet and and 3 ports grouped together in a virtual switch to another subnet. I remember reading that grouping the 4 ports...
View ArticleIssue with EdgeRouter x since upgrade v 1.9
So I have an issue I can not figure out. I have updated the firm ware on my Edgerouter x to 1.9 vs 1.8.5 it was. Since the upgrade i decided I would try the new basic wizard from scratch. So my modem...
View ArticleOpenVPN cipher options on EdgeMax Lite
Hey everybody, After many failed attempts at trying to get OpenVPN up and running, I was finally successful using this guide. Now that it's working, I'm curious about going back and hardening the...
View ArticleClarification on Interface-based matching for Advanced-Queue filters?
I've been attempting to use the Interface "match" in filters in the Advanced Queue (from here-out, "interface-based matching") to direct combined traffic to different interface-based branches, but I...
View Articlecommit-confirm still triggers reboot when commit fails
This is really stupid. Why does the device need to reboot when nothing is committed? All it causes is to lose uncommitted config
View ArticleEdgerouter X move WAN from PPPOE ADSL to DHCP Cable
Preface: I am a relative newby to EdgeOS I have set up my ER-X with an ADSL account using the PPPOE setting on the WAN interface (eth0) bridged to my ADSL modem. I have port forwards set and configured...
View ArticlePort Forward to internal L2TP server
I have an ERL3 on v1.9.0 that just replace a homebrew OpenBSD firewall. I used the Basic Setup wizard for very much a SOHO config. eth0=WAN, eth1/2=bridged LAN ports. I have forwarded the three ports...
View Articleneed help with firewall rules.
without utilizing zone firewalls, i wish to isolate my guest network. eth0(dhcp) = WANswitch0.9 = LAN_GUEST name GUEST_IN { default-action drop description "GUEST in" rule 1 { action accept...
View ArticleER-X and Unifi UAP-AC-LITE - want to delay AP startup
I have a very basic setup with an ER-X (1.8.5) and UAP-AC-Lite: ER-X Port 0: WAN inER-X Port 4: Unifi UAP-AC-LITE via a POE adapter --- (so AP is not powered POE through ER-X; ERX is also on own...
View ArticleOne cpe staton one Edge point r6, 5 subscribers?
Hello guys. I recently deployed my first r6 as a switch with a custom 24v ups. We liked it. Now on I have the following situation, and would like to know if it is feasible or I'm I dreaming. In in a...
View Articleusing static DHCP mapping for DNS lookup & changing the static mapping name
Hi I use a lot of static mac/ip mappings for my DHCP server on my ErLite. Now, the DHCP returns a domain name, and what I'd like is to be able to use that static mapping name, append the domain name of...
View ArticleER-Poe5 ipsec hardware offload not working
I have an er-poe5 with ipsec site to site vpn to another edgerouter lite. It seems like the hw-offload dosent work because when I transfer files over the link I get max 5MB/sec and the cpu is running...
View ArticleIs a static route the solution?
Dear expertsWhile I'm actually a software engineer and not a network engineer, I'm requesting your help. :-)Setup:- Router 1, connected to my ISP (WAN) 192.168.192.1/24- Switch, port based VLAN- Router...
View Articlecombining dnsmasq and custom dns per host
Hi Due to my local host name resolution issue with the standard DHCP, I figured I'd give dnsmasq a try. And Lo behold, I finally get a resolution fo my static hosts (provided I use the fqdn - if...
View Article