Edgerouter X lost LAN side everything. WAN works still...help.
I've setup an edgerouter x with 2 wifi AP's. Everything was working fine until two nights ago when nothing will pull a dhcp address from the lan side. Wifi doesn't show up, it will show up when the...
View ArticleConnecting 2 LAN's over Wireless Link
Hi, I currently have two premises which I have a wireless link between which is working perfectly fine. However, I've always had trouble with local network traffic from one of the LAN's routing through...
View ArticleClik here to view.
Unable to access EdgeRouter POE
Hello! I have been using my EdgeRouter POE 5 port router in my home setup for about 2 years now. Suddenly, the router takes a complete dump. It maintains power, but I've lost all access to it. I've...
View ArticleERL-3, CenturyLink Gigabit, Static IPs
I just bought 8 static IPs from CenturyLink. I have a little table of 8 IP addresses now, the first is "Reserved Network" (1.2.3.1), the next five are "User Assignable" (1.2.3.2-6), then one is...
View ArticleAnyone running a VPLS that doesn't leak memory?
I'm very interested to hear if anyone is running an MPLS VPLS on 1.8.5 for an extended amount of time, without the routers serving as VPLS endpoints leaking memory and ultimately crashing? For...
View ArticleWeekend fail: stuck trying to figure out 5 Public IP address routing (ERL)
I've got a 5 block of IPs from Comcast but I can't get them forwarded properly internally... I want 50.196.239.227 to forward to my internal server, setup as 192.168.1.101 ... As per a previous forum...
View ArticleLose access to ER-X when plugging in Modem
Everything has been fine for months but yesterday we had an AT&T outage in our area and now I can access the Internet when I connect directly to the modem but when I connect to the ER-X I can't...
View ArticleEdge Router POE5 - bridging ports
I want my ER POE5 to feed a 24 port switch on Eth 1 and my three Unifi AP's on Eth 2 - 4. I used the WAN+2LAN2 wizard (firmware 1.85) and find that Eth 1 is on 192.168.1.1 and Eth 2, 3, 4 are on...
View ArticleRecent IPv6 Issues with Comcast (empty radvd.conf)
I've had no issues with IPv6 on my ERX for months, but this week a power outage seems to have caused my to lose my IPv6 address. I'm just trying to ensure nothing is wrong with my ERX setup and in the...
View ArticleERL3 ipsec Site-to-Site terminating on bridge BR1
Hello - I am using an ASA to ERL3 ipsec site-to-site vpn, and it is working! However I am having one problem with the config. I would like to terminate the VPN on the ERL side on a bridge - (The ERL...
View ArticleSSH on a different WAN port?
I like to make the SSH server on my router available from the WAN side (with password auth disabled). I want to keep SSH access from the LAN on port 22 but have it available on the WAN on port 443,...
View ArticleEdgerouter Lite - slow upload speeds
I have an Edgerouter lite. I am getting slow upload speeds. If I jack my laptop into the network demarc, I get the full speed we are paying for : 15x15Mbps symmetrical. With the edgerouter lite in,...
View ArticleLLDP Port Id: MAC address only
I've run into an issue with LLDP and I was hoping somebody could explain to me why on my edgerouter I only see Device ID and no Platform, Cap or Port ID from the router side. On the switch side (to the...
View ArticleLoad balancing with 3+ WAN connections
I'm considering using an EdgeRouter 8 as a load balancing/failover router for a setup with 3 (possibly 4 or 5) WAN connections. I'm not familiar with EdgeOS, but looking at the guide there are wizards...
View ArticleAirPlay Availability on WAN+2LAN2
Hello, I recently purchased and setup a EdgeMax Light for my SOHO setup. I ran through the wizard setting my LAN up as a WAN+2LAN2. The configuration is as follows:eth0 - WAN - DSLeth1 - 192.168.1.*...
View ArticlePort base VLAN
How to set the port base VLAN.Port 1 to port 2,Port 1 to port 3,Port 1 to port 4,........Port 1 to port 8,isolated ports 2-8.
View ArticleUniquely identify an EdgeRouter device
I'd like to identify EdgeRouter devices with a high degree of confidence. I'm aware of 'show version' and md5sum. What would be the most stable and unique files that md5sum could sum across OS...
View ArticleAccess to shared network printer in different subnet
Hello to everyone! Recently I bought EdgeRouter X for my office, which is located inside a large business center. The goal was to make independent subnets for office LAN, WLAN (for security reasons)...
View ArticleClik here to view.
Need buy advice
Hi all, this is the network config at my home at the moment: - Fritz!Box router which at the moment makes everything (modem/router/switch/AP)- Synology NAS (connected to Fritz!Box)- MacMini as home...
View ArticleNAS and PTP routing speed with PowerBeam AC between router and switch
I am running a network with the EdgeRouter LITE and the Edge Switch, with multiple VLANs. If I would to separate the Edgerouter and the Edgeswitch, and bridge the lan port of the router with the...
View Article