DNS setup with Windows DNS server
I promise to read as many posts on DNS as I can tonight... But tomorow morning, I need to have a solution to this situation: 1) Edge Lite router running 1.80 2) Router eth0 as WAN, eth1 as...
View ArticleER-X traffic policy error under v1.8.5
I just installed a brand new ER-X at a customer site. Before installation, I upgraded it to v1.8.5. As part of the install, I set a traffic policy on eth0 using the GUI Config Tree (Man, I love that...
View ArticleER 5 POE
I have an ER 5 POE and I have the ETH2,3,4 tied together acting as a switch. I went ahead and made another DHCP Server on a completely different subnet, How would I go about assigning this DHCP server...
View ArticleIPv6
Hello,there for the CLI, a command which I outputs whether the IPv6 Advertisement Daemon (radvd) running?How can I checkthat?
View Articleupnp2 and firewall
UPNP2 doesn't seem to be working after I put my firewall in place. It is driving me mad as it seems to stop my computer that connects to an exchange server from authorising. Is there anything that I...
View ArticleClik here to view.
Issues with inter-vlan routing
Hi All, I've read quite a few of the forum posts on routing between vlan's, seeing rather inconsistant pings between vlan's which is quite baffling at the moment. First time I've worked with Ubiquiti...
View Articleneed some help with edgepoint
i bought 2 edgepoint r6 ,now i need to configure they act like switch only.i use also sfp ports from eachother.so all 6 port need to be acting like switch only.big thanks.
View ArticleInbound Masquerade for device
Guys, Can i set up an inbound translation rule for an internal device which does not allow public access?I have set up an portforward rule for eth0 to eth2 on port 80 to 192.168.100.21. But the device...
View ArticleMultiple GRE Tunnels (WAN LB) setup to remote site
I am currently working on setting up ERLs at our locations. We have two ISPs at each site, so I am trying to create 2 tunnels to each of our 2 core devices (Vyattas). On the Vyatta I am able to...
View ArticleNot getting local DNS to work properly
I have tried to set up a new Edgerouter Lite, but I'm not getting Local DNS to work properly. I can see the name b3 to lookup in /etc/hosts, but when i do a nslookup, it says "*** UnKnown can't find...
View ArticleIPTV Traffic Analysis
After doing a lot of reading here in the forums I was able to upgrade my two day old “EdgeRouter X” to firmware version 1.8.5 and configure it so that it would pass the traffic for IPTV. When looking...
View ArticleIPsec tunnel up but no traffic after router
Tunnel is up on both ends. Routers can ping each other. The workstation behind the routers can also ping the far router. I can't ping a far workstation on either side from either the router or the...
View ArticleNat Issues
I'm having issues with Nat. I have 2 static public ip addresses. 1.1.1.1 and 2.2.2.2 The wan interface is using 1.1.1.1 as the main ip and 2.2.2.2 as the second ip. My lan is Natted to 1.1.1.1 and...
View ArticleEdgeRouter Lite 3 - trunk port
Hi, how I can turn on port trunk via WWW? On my router I want create: eth0 pppoeeth1: vlan1, vlan100, vlan120, vlan140eth2: off I know how to do but I don't know how I can enable trunk port? My switch...
View ArticleNeed some help on EdgeMAX Edge Router PoE 5 New to Ubiquiti Gear
Needed new gear due to age and problems of the home network. Wireless - Linksys WAP54gv2 replaced by Unifi AP AC Pro. Had to keep resetting the Linksys by getting ladder to remove power and force a...
View ArticleHelp with firewall rule to access Unifi Video
Hello I'm looking for some help with firewall rule to access my NVR. I setup the Edgerouter lite with the wizard so I have default rules as follows (eth1 my internet) WAN_IN - eth1/in - Default drop -...
View ArticleTraffic Analysis host name resolution?
I have noticed that only one host listed on my Traffic Analysis page shows the hostname in addition to the IP. The others just show IP. How is host name resolution handled on that page? This is on an...
View ArticleNew SOHO Installation
I just purchased my first EdgeRouter X. I immediately upgraded the firmware to 1.8.5 and then used the "WAN+2LAN2" wizard. I also added a couple of port forwards for my e-mail server (TCP ports 25...
View Articledefault Firewall setting enough?
I have successfully connected my ERl and AP AC Lite. I am very happy with the setup. I have confiured my router for uPNP so my Qnap could auto config the setting for it's self. When I was checking...
View ArticleClik here to view.
EdgeRouter PoE5, a bunch of VLANs and routing between them...
Now that I have a stable configuration, it's time to do fancy/crazy things... Got my hands on a couple of managed switches and was wondering how hard/bad/horrible it would be to do something like...
View Article