Can't Connect EdgePoint S-16 and EdgePoint R-6 with SFP fiber
Hi, How do you guys connect S-16 and R-6 with fiber?I am unable to connect them together. I've done some test with different gear without any usefull results. Please check it out, maybe it helps...
View ArticleTrack / Log port state
Hello, I have a Edge-Lite, hopefully this is the right place to ask this question (please direct me elsewhere if it's not). Is there a way I can track / log the sate of the WAN port (eth1) on my...
View ArticleEdgeMAX limiting access to the UI
We have an 8 port EdgeRouter with five active subnets all running on it. However, I only want the UI to be available on one subnet or one eth port to prevent other clinets on the network getting access...
View ArticleManagment ports on edgerouter
What are the management ports for the edgerouter?On the guest network (192.168.2.0/24 subnet), I want to block the guest from loggin in to my router (192.168.2.1), but allow everything else. What is...
View ArticleAdvanced QoS per client
Is it possible using the new advanced QoS settings to put in place bandwidth limits per client per application category. So for example limit dl for streaming media to 500kbps per client device?
View Articleany risks of using 0.0.0.0 as local-ip of gre tunnel?
I am trying to make a reusable configuration for an edgerouter that i can reuse at multiple similar locations. The configuration includes establishing a gre tunnel to a central server. The WAN ip of...
View ArticleTraffic Policy Limit Download and Upload Bandwidth by "x"kbit / mbit vs....
I am running QOS using this as my guideline: https://help.ubnt.com/hc/en-us/articles/205198380-EdgeMAX-Quality-of-Service-for-Voice-Over-IP-Qos-for-VoIP- It is working great but I only have one VOIP...
View Articleneed help with ipsec vpn juniper srx 240 to edgerouter
Hi,So we are setting up an ipsec vpn tunnel between two site's.Tunnel is succes we have both ike and ipsec sa up But for some reason we can't push any traffic over it.Can you guys help us on what we...
View ArticleHow to set up DSL modem in trans. bridge mode for admin port
So I have an Actiontec 784 modem in transparent bridge mode. IP address to eth0 is assigned by the telco via DHCP. Everything works as it should. It has 4 ports of wired ethernet on it. The first...
View ArticleTying in MPLS to rest of the network.
I have two sites connected with a L3MPLS. The MPLS provider has routers on each end, and have BGP routes advertised for both sites. Site A is advertised as 10.10.6.0/24 and site B is advertised as...
View ArticleClik here to view.
CLI - changing Static IP
Hi, To change the static IP of a device and in many cases I'm also changing the host name do I need to delete the original static IP and then add it back? What are the commands especially if I need to...
View ArticleWAN keeps dropping, but DHCP renew fixes it
Hey, I'm new to home networking, but have been enjoying an ERL and UAPACPRO for the past month or so. I have a very simple setup, that I used the wizard for, where eth0 is connected to my ISP and where...
View ArticleER-X QoS setup
Hello guys,a friend of mine who needs a new network design called me for his install. He has a bar (a lot of people connecting to WiFi)ADSL Modem (~10/1) in bridge mode. I will get for him an UAP-AC-LR...
View ArticleFirewall - Newbie Help
Looking for some help for a newbie. I have one last device to get working on my setup. I have setup one Vlan on my system for a couple of devices. I have the EdgeRouter 5 poe with 1.8 firmware. I...
View ArticleHow to load balance a VPN connection for failover
Hi. I've read some topics regarding VPNs + load balance but I didn't found anything specific to this. I've setted an OpenVPN tunnel and I have load balancing for 2 WAN connections, I followed a...
View ArticleOverride DSCP value on data to WAN?
Is it possible to change the DSCP value on packets going to WAN? I'm looking at Tmobile WiFiCalling where the data is inside IPSEC tunnel with TOS=0x50 which I think translate toDSCP=20 (decimal) I...
View Articledual stack IPv4 & IPv6 DNS forwarding
Hi, I just got the EdgeRouter X , upgraded it to v1.8.0. I am finding that if I have my WAN port set to more than 1 IP address from DHCP that it only uses the DNS nameservers from the last connection...
View ArticleEdgeMax Not Retaining Configuration
Hi Guys So Im sort of new to EdgeMax and Im having an issue with it at the moment. Yesterday I configured and tested a whole lot of bridges and VLAN's which were all up and running. However this...
View ArticleIn Search Of - Your Old Hardware
Do you have old EdgeRouters sitting around that don't work? Do you want to get rid of them? I am looking for non functioning EdgeRouters (or other brands too). PM me or comment here!
View Article