Need help QOS on Google Drive/Dropbox (desktop app)
Hello, we have an office of about ~20 people. We only have a 20/20 symmetric connection with our ISP. We use an Edgemax Lite Router with 3 Unifi AP Pros. Is there a way for me to configure QOS or...
View ArticleClik here to view.
VPN IPSec Site-to-Site to Sonicwall TZ205
Hello I have a new EdgeMAX Router and would like to configure a VPN Connection to my "old" Sonicwall TZ205.But at this moment I don't show the reason for this. I have configure my EdgeMAX with this...
View ArticleOpenVPN site-to-site - Static Route (sometimes) Stops Working on Reconnect
I followed the guide here: https://help.ubnt.com/hc/en-us/articles/204949694-EdgeMAX-OpenVPN-Site-to-Site to set up site to site VPNs from my head office (site 1) to 3 branch locations (sites 2 through...
View ArticleEdgeRouter Lite?
How to configure NAT port 1433, only accept origins of certain IPs?Example:SQL 1433 ip 192.168.1.251Edgerouter 1433 IP 200.234.33.90Client 1: IP 178.33.22.22Client 2: IP 200.33.44.33Client 3: IP...
View Articlebogux-nxdomain option in dnsmasq
In porting settings from my old router setup over to Edgemax, I've run into an issue with the bogus-nxdomain directive. This post seems to indicate it's not possible to use it in the /etc/dnsmasq.conf...
View ArticleClik here to view.
esx on ER8 switch port, can't quite get it
I have an ESX host connected to an ER8 port (single NIC, both management and guests)It has a management IP on the 192.168.10.0 subnetThe guest running on the host has several ip addresses:eth0...
View ArticleErLite-3 IPsec site-to-site slow speeds
Just set up an IPsec tunnel between two remote Edgerouter Lites, both on v. 1.8.0, but tunnel speed is only barely faster than OpenVPN. Site1 subnet 192.168.37.0/24 -- WAN speed: 75mbps Up / 75 mbps...
View ArticleInitial config on a Edge Router X SFP
This is my 1st attempt on getting the router up and going. Following support's recommendation, I have configured the following; Eth0 is configured and working as my WAN and is connected to my ISP.Eth1...
View Articlev1.8.0 Bug
To replicate:1. Edit a ruleset2. Add new rule3. under Protocol, select Enter a protocol number, in the edit box, enter 80,4434. under Protocol, change it to All protocols5. Save Error appears: Invalid...
View ArticleRoutes for DNS forwarding?
I'm in a config with 6 WAN in load balancing on an ER-8 (1.8.5b2), using modem/routers from several ISP, with a minimal setup service { /*..*/ dns { forwarding { cache-size 600 listen-on eth0 } } }The...
View ArticleCan only scan 1st LAN when PPTP VPNning to edgerouter
Setup is simple; WAN = eth0LAN1 = eth1 192.168.3.0/24LAN2 = eth2 192.168.9.0/24 When connecting via PPTP VPN from external to the Edgerouter(allowed from only 1 external IP to try and make pptp a...
View ArticleEveryone should read this: How to backup your EdgePro for the case of MMC /...
Dear all, als U is not providing any recovery information, I will try to help a bit. There are serious issues with the partitioning that U is using. If the filesystem gets corrupt everything goes...
View ArticleEdgeRouter X (ER-X) v1.8.0 (v1.8.5beta2) Kernel panic
We're running an ER-X with a working VPLS to a MT RB.All of a sudden the ER-X hangs (v1.8.5beta2) or reboots (v1.8.0).I've managed to capture the potential error with syslog: 05-25-2016 12:49:36...
View ArticleHire Somebody for QOS Setup Gig for Mitel 5330 VOIP Phone with EdgeMax
I am able to configure the basics of my EdgeMax through the GUI but am a total newbie with the CLI. I love learning new stuff but I just want to get this done. Is there somebody I could pay to...
View ArticleClik here to view.
Help needed on mapping ISP provided WAN IPs to internal LAN IP
Hi all, I've been struggling to get this to work following the linkFirmware used is 1.8.0 on the Edgerouter Lite. I've managed to follow each and every step but for some weird resaon, the WAN IP i...
View ArticleAdvanced Queue Limit and Configuration Best Practices
I'm curious why there is a 1024 queue ID limit with advanced queue. I'm also curious how if queue IDs are set to service lower (numerically) when targeting a specified source/destination, how do you...
View ArticleSetting smart qos for flash streaming ubnt edgerouter lite
Hi, We have a small setup using edgerouter lite:1x WAN port that connects to ADSL modem.LAN1 192.168.178.1LAN2 192.168.179.1bridge LAN1 and LAN2. The original idea was for LAN1 = LAN, LAN2 = WIFI only....
View ArticleScheduling firewall or QoS changes based on time interval?
I know that you can schedule basic firewall changes via the Web UI with start/stop times for specific days of the week. However - how would you schedule more advanced time changes - for example, on an...
View ArticleComprehensive Command Reference
Please provide a comprehensive command reference guide for all relevant versions of EdgeOS. I have been trying (semi-successfully) for the last month to create an IPSEC tunnel between two ERLs, and...
View ArticleClik here to view.
2 ERLs with WAN failover in HA
Hi Everyone, I have two ERLs in HA (topo in the picture). Both uplinks are configured with public IPs and I use NAT on both routers. This config works good. When I configure WAN failover feature and...
View Article