Clik here to view.
Port forwarding not working help
Hi,I am trying open a port for a game but I seem to be unable to get it to work and I require some help. Network SetupISP Modem -> EdgeRouter X (v1.9.0 ) -> NanoBeam 5AC 16 (v7.2.4) in Access...
View Articleroute one device over ipsec
Hi All I'm trying to acheive a setup where I have a single device routed over an ipsec VPN tunnel - I've found a few tutorials to do this with openVPN but I wanted to take advantage of the acceleration...
View ArticleHow to add second tunnel to ERX
I have an EdgeRouter X with working IPSec VPN to a Cisco RV320 in one office in Asia that I set from the CLI following this example that I found here: VPNset vpn ipsec auto-firewall-nat-exclude...
View ArticleClik here to view.
EdgeMax WAN traffic on eth0 WAY higher than LAN traffic
Hey guys, I apologize if this is obvious, but I am stumped. My WAN traffic (specifically transmit) is periodically going through the roof, sometimes to 300-500Mbits (no that is not a misprint...I...
View ArticleERL3, PPPoE disconnect problem
I've experienced this twice now: my WAN/PPPoE connection disconnects and ERL3 does not successfully reconnect. The first time, I just rebooted ERL3 and it started working again.This time, I did a...
View ArticleUnifi Controller for edgerouter lite?
The unifi controller page shows really nice screenshots of for example traffic statistics...How can I see as detailed and nice graphics for data from my edgerouter lite?It feels lite the...
View ArticleCPU Frequency mistake
I was setting up a new router and noticed that frequency is misspelt. Linux version 3.10.14-UBNT (root@edgeos-builder2) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 SMP Fri Jul 29 16:53:39 PDT 2016The...
View ArticleClik here to view.
Issues Setting Up EdgeRouter and EdgeSwitch
I am trying to setup a new home network using UBNT equipment (in lieu of prior Cisco equipment I sold off before moving). Right now my network is in the early stages of being architectured out but I am...
View ArticleClik here to view.
Same IP Pool on different VLAN with same fixed IP's
For our R&D department we need the following: 4 x VLAN with internet access. Every VLAN needs a DHCP server within the 192.168.0.xx pool. Hardware on every VLAN has fixed IP's.We like to use this...
View Articleopen vpn tunnel - do a one way acces
So i want to create a vpn beetween two office (office A et office B).It already works.But only the office A can acces to office B, Office B cannot acces office A. What's the best way to do it ? So here...
View ArticleOpenVPN Performance
Hello,I am a new user of the ERL and I am very pleased with it at the moment.I would like to know if it is planned to make OpenVPN faster (through HW offload) ?Or is there any other tips to make it...
View ArticleDigium Phones DPMA and IPSEC?
Has anyone here had any luck getting Digium Phones using DMPA to *provision* over a site-to-site IPSEC VPN connection (ERL3 in my case)? If I provision the phone in the core network, it will work as...
View ArticleERL Slow ipsec Performance
Hello everyone,I am currently testing an ipsec site2site tunnel with my Edgerouter Lite and a Linux server.The Tunnel itself is working, but the Performance is quite Bad.With Iperf i get around 48...
View ArticleOpenVPN Bride - Routing or Firewalling missed?
Hello, I have following two site setup. Configuration was done based on some UBNT guides. == Site A ==16M DSL Connection, Fritz!Box as Modem/RouterER-PoE (eth2) connected to LAN on Fritz!Box, Device on...
View ArticleIPSec S2S tunnel issue with Cisco ASA Spoke to Hub Topology
Hello, I have a question that is maybe easy to answer as I believe i'm missing something small regarding IPSec Site2Site communication. Target: I am trying to implement a cost effective solution using...
View ArticleLoad balance config check, strange readings.....
Hi, running an EdgeRouter 8 port with load balancing configured over 4 WAN interfaces. Currently one of the WAN interfaces (ppppoe2) is down and not functioning. Ive set the weighting on pppoe0 &...
View ArticleWAN failover questions
I have a few basic questions about how to set up WAN failover load balancing. I'm a relative newbie, but I've been reading and I'm starting to understand. Still, there are fundamental gaps in my...
View ArticleHow do I clear an active NAT translation?
With Cisco, I used to use the clear ip nat translations x.x.x.x command to clear an individual address or I could use the clear ip nat translations * to clear the whole table. I haven't been able to...
View ArticleNetwork layout
hello allDue to physical limitations at a site I am working on I have Internet coming in off if a tower and being feed into a picostation in SOHO mode. is then another Pico station that feeds into a...
View Articledns to .d42 tlds dont work
HI, I'm currently playing arount with dn42. Everything works so far. (BGP, OpenVpnTunnel,..) but i cannot resolve the .dn42 tlds. it works with dig directly on the erpro.. config:...
View Article