PBR - 2 WAN, Failover, Exclude VLAN's on Failover and Unknown ISP IP's
Hello out there, im quiet a bit new to PBR and firewalls and so, i worked through many articels on this site. It would be really nice if someone could pls review my work, give me some hints and help me...
View ArticleTraffic Analysis - when to use
Hello all,I have a question about traffic analysis on the ERPOE-5. Are there any negative effects of leaving it on all the time or for an extended period? IE does it use up a lot of memory, take up a...
View ArticleVRRP on the WAN side: any caveats?
I am considering a pair of EdgeRouter Pros for a HA firewall setup. This will replace a single enterprise-grade firewall. I have done some research, but would appreciate a sanity check! The ISP hands...
View ArticleComcast EDI to EPL change
Community,We are currently testing Ubiquiti as a solution to replace are Cisco products at our branch office. Currently we have Comcast Metro Ethernet EDI 8mbps/8mbps which is later a simple L2L ( lan...
View ArticleI think I lost router access [embarrassed] but still have DHCP access
Hello everyone, This is a little embarassing. In my attempt to VPN my personal laptop into my work VPN server, the IT support staff said I needed to change the IP address of my router from 192.168.1.1...
View Articleipv4 and ipv6 firewall rules
I'm new at this and a little confused. I had an existing ipv4 configuration working and wanted to enable ipv6 capability. I assumed I would keep the ipv4 firewall rules (WAN_IN and WAN_LOCAL) and...
View ArticleEdgerouter PoE rebooting when Unifi AP Pro plugged in?
Got a Edgerouter PoE and a UniFi Pro AP. I run the WAN+2LAN wizard to set it up, then pick eth3 as the PoE at 48V but when I plug in the cat5 the lights go off on the router for few seconds and I can't...
View ArticleAllow ping through to multiple IPs
I'm new to Ubiquiti routers. I have a block of 13 IP addresses and they are configured on ETH0 and go to ETH2 (LAN). I've got the ports forwarding through for RDP to each server without problems. I...
View ArticleIPsec Site-to-Site VPN with Edgerouter and Netgear
Hi I am implementing my new router into our existing network, we have 3 locations and all have same models of Netgear routers. I was wondering if it's possible to do VPN between netgear and...
View ArticleEdgeRouter grabbing two IP addresses via DHCP on WAN
I have an EdgeRouter set up with DHCP for the WAN/Internet interface on eth0.For some reason, it keeps pulling two IP addresses and I can't figure out why. When I renew the lease, one IP shows up on...
View ArticleRestrict NTPD interfaces
I've noticed that the NTP daemon appears to be listening on all the available interfaces on my router: david@erx# sudo netstat -a -n -p ... udp 0 0 10.0.4.1:123 0.0.0.0:* 30654/ntpd udp 0 0...
View ArticleEdgeRouter interface config UI glitch?
On the interface config window for eth0 (set up as WAN/Internet) there is a strange blank box to the left of "Renew" when address is set to "Use DHCP". See attached screenshot. What is supposed to show...
View ArticleHow to clear screen using CLI console from Web UI
How do you clear the console screen when using the CLI console from the Web UI?I'm sure it's something easy. Thanks!
View ArticleRemote syslog server for network connections
Hi,Is there any way to keep log of nat connections (internal ip towards external ip) ? This is for security issues ( customers hackers, child pornography etc. etc.) I saw the remote log option. Does...
View ArticleMultiple IP addresses and NAT
Hi, I have an issue when using EdgeOS v1.8. I previously had 1.6 installed with multiple IP addresses assigned to an interface (my ISP is providing a /28 and I have all the addresses setup on the...
View ArticleClik here to view.
Not able to view 'some' webpages after unexpected reboot
Hi I have an EdgeRouter Pro on 1.8.0. It was working fine last evening, until one of the fuses in the house blew and it rebooted. When it came back up, I found that some webpages could not be...
View ArticleOld DHCP entries stuck in hosts file
I've set the following on my EdgeRouter: set service dhcp-server hostfile-update enable This works great so that new DHCP lease hostnames are added to the hosts file of the router. This is invaluable...
View Articleerlite3 only ½ pages load
hi, ubnt@ubnt:~$ show version Version: v1.6.0 Build ID: 4716006 Build on: 10/31/14 17:31 Copyright: 2012-2014 Ubiquiti Networks, Inc. HW model: EdgeRouter Lite 3-Port HW S/N: DC9FDB802B08 Uptime:...
View ArticleClik here to view.
DNat Group forwarding help needed
i have a ERPoe-5 and need some help with setting up DNat. When i use Port forwarding it works fine, but i have lists of ports i need to forward, and dont really want to have to do 100+ rules. I would...
View ArticleIssues with seeing devices on the network
I've setup a new EdgeRouter Pro. I have Eth2 as the LAN plugged into our switch. Eth3/Eth4 are Ubiquity APs. Everything can get on the internet fine, but nothing can see internal traffic - i.e. the...
View Article