Router X SFP bootloader corrupted
I have somehow corrupted my Router X SFP bootloader. I tired to correct this by opening up the screws and connecting to it via Serial port. I have successfully connected to the router via serial, but...
View ArticleEdgemax sfp VPN Please help.
Hello All newbie here,Question 1. Has anyone been able to use private Internet access and have plex working?Question 2. Has anyone used versavpn and did plex work?Question 3. Now the real question how...
View ArticleDuplicate IPv6 address for interface in GUI after upgrade to 1.8.5
I recently (hah!) upgraded my ERL3 from 1.8.0 to 1.8.5. The GUI is now showing an extra (and redundant) IPv6 address for eth0. Previously, only my /128 was shown in the GUI. Here is what the CLI says...
View ArticleClik here to view.
External IP Addresses in DPI after 1.8.5 Upgrade
I am seeing external IP address in DPI after the 1.8.5 upgrade. Is anyone else seeing external IP addresses in their DPI? I never saw these before the upgrade.
View Article(ER-8) HELP MEEEEEEEEEEEEEEEEEEEE!
Hi! I have a thing.It's an ER-8. I like it, but the UI is confusing to me. And, since I'm CLI deficient, I literally do *NOT* know how to set up what I need to set up. My needs:- 1 VLAN using ports 1...
View ArticleIPv6 SLAAC not working after upgraded to 1.8.5
Something strange is going on since upgrading to 1.8.5. My IPv6 SLAAC setup is no longer working with my AT&T Uverse setup. See the following config: firewall {all-ping enablebroadcast-ping...
View ArticleFirewall Advice
Can someone help me with the below firewall? Here is my port configuration on the ER-Pro:eth0: WANeth1: LAN, connected via UniFi 48-port PoE Switch -- 1.2 and 1.3 are VLAN's, see beloweth2:...
View ArticleAdvanced-Queue best practices
I created a download/upload branch, and leafs according to which service(s) I wanted to shape. Unfortunately, I can get shaping to DPI shape streaming with a burst before settling at a lower data...
View ArticleDHCP relay over VTI
Hi, I am having trouble using DHCP relay over VTI. This is my current configuration: firewall { all-ping enable broadcast-ping disable ipv6-receive-redirects disable ipv6-src-route disable ip-src-route...
View ArticleIPv6 Webpass Help
I'm having trouble configuring ipv6 for my residential network. I've gotten an ipv6 address from my ISP (webpass), but from what I understand of ipv6 (admittedly little), it looks like they're only...
View ArticleUnable to upgrade firmware - Not enough disk space for root file system
Hi all, First time posting here so please be kind. I am trying to upgrade my ER-X to software release v1.8.5 with the new image posted today but am having issues with not enough space to upload the...
View ArticleClik here to view.
USG Recovery Procedure
This worked for me with a 3-port USG that would not boot due to a corrupted USD Flash drive Remove USB stick from a good USGCopy to a binary image file with...
View ArticleSite-to-site vpn with rsasig Certificate for authentication...
Hi All, I posted this on the USG forum https://community.ubnt.com/t5/UniFi-Routing-Switching/Site-To-Site-VPN-w-Certificate-dynamic-wan-ip/m-p/1591414#U1591414 but since I also need to setup a similar...
View ArticleChecking the configuration of QoS
Hello.I need to doQoSperIP192.168.1.254/32with120Mbdownloadandupload15mbor configuration I did good? traffic-control {advanced-queue {branch {queue 11 {bandwidth 120mbitparent 1}}filters {match 11...
View ArticleEdge OS 1.8.5 IGMPv3
[quote][IGMPproxy]ApplypatchforIGMPv3support.SuggestedbyandDiscussedwith jakbeatz BranoBDremonjjrkdkhereand here.[/quote]Does this mean that can be appliedto thepatchofMCproxy?Can they set aguide to...
View ArticleEdgeMAX eth1 and eth2 are showing disconnected
I just set up PoE on eth1-3 (24v). I plugged it in but computers and the phones that need PoE are not being seen on the router. I just switched it out and the last little switch was working just fine.
View ArticleClik here to view.
EdgeOS 1.8.5 - need more than eight load-balancing targets
It pains me to say write this out loud, but I have a special project going on next week where I would need to load-balance between twelve PPPoE uplinks on an EdgeRouter Pro. The release notes state,...
View Articlehelp with OpenVPN client setup
Hi, I have a very basic WAN + LAN soho setup on an Edgerouter POE with 2 Unifi APs. All of that is working great (I love it!), but the last thing I'm trying to setup is an OpenVPN client connection...
View Article1.8.5 IPSec upgraded from 1.7 broken
Hi, I have a 2 Wan 1 Lan ERL running 1.8.5. I am having issues connecting to another ERL running 1.85. I have 2 tunnels. House ERL runing 1.7 works fine Office ERL show as UP on the VPN status but...
View ArticleClik here to view.
Can't update to 1.8.5 - alway this error
Hi, yesterday, I tried using the WebUI to upgrade to 1.8.5 version of EdgeOS. It failed at copying it. So I tried a reboot, and it fail at reboot! and I tried a SSH or CLI button in WebGUI, and it...
View Article