IPV6 Out of the box
Can an Edgerouter X loaded with the latest firmware allow an end user to obtain IPV6 addresses from their ISP (Comcast) without any special knowledge or CLI? If so, how? Thanks a million!
View ArticleKIS 2016 v.16.0.1.614
FYI:Since updating Kaspersky Internet Security (KIS) to v.16.0.1.614, Kaspersky is now flagging EdgeMax Router as a threat do to a sel signed certificate."Cannot guarantee authenticity of the domain to...
View ArticleClik here to view.
Prevent VLAN routing
Hey guys Been reading up on vlan routing - I'm a little confused can you help me please? I have an edgerouter poe and Im running the following networks at home: native lan 10.10.8.0/24 << this is...
View ArticleEdge router X - througput
hi all; i am looking to get wireless internet enabled for a large hall. currently their is fibre internet connected, and the ISP supplied router is crap. I am looking to have a dedicated router and...
View Article2nd Lan - Edge Router 8 Port
Hi All, Bit of a newbie to Ubiquiti so hoping someone can help. :-0 I have set up my ER 8 using the WIzard - Everything is working well. (Using Load Balance Wizard) eth0 = wan1 (Static Addres from...
View ArticleReserve IP or Have odd DHCP range?
I can't figure out how to do this with the edge router lite.. I have done it with a sonicwall, but it allowed me to do mutiple DHCP lease ranges on a single interface. So I just omitted the statics...
View ArticleVLAN subinterfaces with the same VLAN ID?
So if I create a VLAN 10 subinterface for both eth1 and eth2, what happens? The device accepted the configuration. Does it actually work just like a big L2 domain sharing the same L3 VLAN interface?...
View ArticleEdgerouter Lite - PPTP not connecting from outside the network
Using my phone (tmobile, S7) as a test device. When connected to wifi (on the network), PPTP connects instantly. When connected to the tmobile network or to a nearby xfinity wifi network, I see no...
View ArticleIPv6 question... probably did something stupid...
Hi folks, brand new EdgeRouter owner! Was running a Asus RT-N66U, and was sick and tired of it going bonkers every now and then (especially with high wifi load). So bought a EdgeRouter PoE and a Unifi...
View ArticleERL Lost load balance after setting up Ad Blocking
I'm sure it's something I'm missing here... But I've been pulling my hair out on this since I discovered this afternoon the ad blocking I turned up last night has hosed my load balancing. The ad...
View ArticleVPN
If UBNT is never going to get around to putting the OpenVpn into the GUI properly, could you at least enable SSTP ? PPTP is really getting to be a unreliable option...
View ArticleEdgerouter Pro - No SSH or Web
I've setup the Edgerouter Pro with BGP announcing our IPv4 and IPv6. It ran beautyfully, but now it seems I've lost connectivity to it. ~ $ nmap <router ip>Starting Nmap 6.46 ( http://nmap.org )...
View ArticleVLAN - No IP-address from DHCP
Hello We have issues with the DHCP and guest VLAN. We have following setup. ER-PRO (v1.8.0) with:eth0 – WAN 1 (PPPoE)eth1 – WAN 2 (static IP)eth2 – LAN privateeth2.20 – VLAN GUESTLoad-Balancing between...
View ArticleBlock URL based on MAC or IP Address?
Is there a way to block URLs based on a certain MAC address? Or, if not, based on a certain IP address? Then I would need to force-assign an IP address to a specific MAC address though, in the DHCP...
View ArticleERL: abismal performance of bridge (only 1/4th of the bandwith, without CPU...
My setup consists of two sites connected via ERL's: ERL1 and ERL2. Each site has a Fiber optic connection to the internet. Site 1 has a simmetric 200mbs/200mbs connection (Download/Upload)Site 2 has a...
View Article1.8.5
I just want to take a minute to thank the hard working team at Ubiquiti for the release of 1.8.5. Infact, thank you for all the releases(for all products) and bringing us top shelf equipment at...
View ArticleUpgrade from 1.7.0 to 1.8.5 breaks IPSEC
I just upgraded my router from 1.7.0 to 1.8.5 and had to down grade it again because the IPSEC VPN would not come online. Very similar to what I reported in this thread when 1.8.0 came out. I can...
View ArticleDNSSEC & dnsmasq with EdgeRouter 1.8.5
This part of the latest 1.8.5 release caught my eye: "[DNS forwarding] Update the underlying dnsmasq software to the current version 2.75, now building/packaging it ourselves. The new version includes...
View ArticleUpgrade from Web UI
I was trying to upgrade my ER-L from 1.8.0 to 1.8.5 via the web UI using Safari and it wouldn't work. It would get stuck spinning on the upload. I ended up doing the upgrade via CLI (probably the way I...
View ArticleClik here to view.
Looking to get a new ER-Pro soon. What products will be released that I would...
Forst of all, thanks for 1.8.5!So I want to get a new firewall/router, as my uncle is getting gigabit internet, and I am going to give him my old ERLite-3. I figured instead of getting just another...
View Article