System Log on switch0
Edgerouter ER-X 1.9.0I have eth0 unchanged as 192.168.1.1/24, but the "System Log" to PC 192.168.1.11 (fixed IP) don't work. Can I change this? I would be the best solution.eth1 is WAN.If eth2 is the...
View ArticleVPN options and and using non-standard ports
Do I understand correctly that the following are the options for a VPN server to allow access from a PC, from least secure to most secure: PPTPL2TPL2TP over IPSEC I want to set up my ER-X on my home...
View Articlev1.9.1 bgp "denied due to non-connected next-hop"
It seems that bgp is advertising the wrong next hop ip in some instances therefore a recieving router is not populated with all routes. R1 <---> R2 <---> R3 v1.9.1 - v1.9.1 -...
View Articleedgerouter x and tagging vlan for iptv
Hi, I'm having problems tagging a port with VLAN ID 501 to access iptv from my ISP. When setting up the router I use the WAN2LAN2 configuration, and then I try to add a VLAN interface on eth1. When...
View ArticleOSPF6 Panic/Crash [v1.7.0]
We have an ER that has crashed twice with the following trace: PANIC !! Something has gone wrong with ospf6_route_table[0x77f00800] table count = 26, real number = 25 DUMP START...
View ArticleHow to assign public IP addresses on the ERLite lan port
hi, I just got my edgerouter pro installed and hooked up a rj45 cable to eth0. I then went through the basic wizard and got a public IPv4 adress and Internet working fine. My goal now is to get the...
View ArticleSystem Log on switch0
Edgerouter ER-XI have on eth0 unchanged 192.168.1.1/24, but the syslog to PC 192.168.1.11 (fixed IP) is not possibel. Can I change this?eth1 is WAN.If eth2 is LAN (DHCP) I can syslog on a PC of this...
View ArticleClik here to view.
edgeroter x sfp
Hello,First of all sorry for my english(I'm from Poland) .I have router from huawei-e5186 and i have one question-if the e5186 haven't got bridge mode, will i have any problems with connection between...
View ArticleEdgerouter Load-balancing delete wan route after all path failed
Hello, I use Edgerouter v.1.9.0 I have two WAN, and I want to failover only, not load balance. When both links are down, and after a while, they came up again, the edge is not able to restore...
View ArticleEdgeMax + UniFi AP + Multiple VLANs
I just purchased a ERPOE-5 and am having issues setting it up.Here is what I'm trying to do:1. Use eth0 for Internet2. Use eth1 for my primary 192.168.4.0/24 network3. Use eth2 for secondary subnets...
View ArticleEdgerouter lite 1.7 Hub/Spoke Site-to-Site VPN issues - NEWBIE user
Hello to all - New user here and have zero experience with CLI, so everything is done via GUI. Any pointers to help me resolve my issues would be appreciated. I was a CCIE for almost 20 years, so the...
View Article1.9.1 Firmware Update Check
Is there any configuration for this, specifically to enable/disable?
View ArticleTrouble Splitting Eth Ports/ IP's
Hello- Total newbie. Sorry. I have a new fiber connection set up in my main store 20x 20 Mbps. We also have a fiber link set up between our second location 5 x 5(Mbps) as a bridge. I have a few...
View ArticleClik here to view.
ERX uboot error/failed?
I picked up this switch from Amazon recently, used. When I plug in the power switch, I get a power light and after a few seconds, a LAN port will light, if a cable is plugged in, but no IP address will...
View ArticleEdgeRouter Lite not passing AP traffic
So I just installed an EdgeRouter lite and would like to hook ap a UniFi AP AC PRO to it. I can get out to the internet when my laptop is plugged into it. However as soon as I plug in the AP nothing...
View ArticleEdgeRouter X Port Forwarding - Dysfunction
Dear All,I try to get Port Forwarding up and running on my newly installed EdgeRouter X. Please take a look at my screenshots attached - to get a better understanding for my settings.I try to get a...
View ArticleERX SFP eth5 1000/full to auto
Hello, I was using the alpha version of the ERX SFP (1.9.1) and noticed the changes about interface configuration (from 1000/full to auto). It makes me some troubles when connecting it today to an ES...
View ArticleEdgeRouter X-SPF as a switch with a port mirror
I'm quite new to routers thus excuse me for my dumb questions or ideas. I found an edgerouter x-spf for use and I was hoping to use it as a switch for my current network and mirror the ports to an...
View ArticleStill stumped 3CX behind NAT
Here is my setup:3CX on Debian linux on a static IP on my LANExternal SIP providers out on internetAll sip phones on same LAN as the 3CX I have previously run PBXs behind the Edgemax with no ports...
View ArticleMultiple IP WAN : auto firewall, NAT and port forwarding
Hello, I would like to have an easy setup for my firewall, NAT and port forwarding My ISP offers me two WAN IP (x.x.x.1 and x.x.x.2) (eth0) and I have two separate LAN on my network 192.168.1.0/24...
View Article