PPPoE / routing CRITICAL problem with 1.9.0
Hello,Today we have upgraded one of our ER Pro to 1.9.0 (from 1.7.0) and at first look everything was ok, but then some users complained that internet is not workig for them.I have checked that and i...
View ArticleRandomly losing IPv6 connectivity
I have a very strange problem where at random occasions, I lose all IPv6 connectivity. At first, everything works perfectly, but all of a sudden I can't access any IPv6 addresses on the Internet. I've...
View ArticleOpenVPN with auth-pam.pl or user/pass authentication
Hi guys, ERL 31.8.5 I am currently running an OpenVPN roadwarrior setup with certificate based authentication only. I would like to add user/pass for two factor auth. OpenVPN provides the auth-pam.pl...
View ArticleVPN Crashing ER Pro 8
Firmware 1.9.0. I have attached a screen shot of my IPSec config. As soon as I hit commit on this configuration the ER becomes completely unresponsive (no ping, etc) until I power down and reboot. What...
View Articlefailover only not working as expectged
Hey all, another question for you. the ER-3 lite I have on a customer site often sees high bandwidth utilization. they have a 15 meg bidirectional pipe from a wireless internet provider that does fixed...
View ArticleSecond dnsmasq instance
Just sharing :-) If some hosts on on the LAN need to use alternative DNS servers but still should be able to resolve local hosts' names this can be arranged by running a secong dnsmasq instance on the...
View ArticleClik here to view.
Need help setting up a Edgerouter Pro 8
Hello all, My current setup Cisco Rv042(192.168.17.1): four lan ports connected to four Unifi AP(192.168.17.2,.3.4.5) The reason i have four aps is because i have about 100 chromebooks that connect to...
View Article2 WANs. IPsec an output via the backup channel.
Hello! There are two main channel (1.1.1.1) and a backup (2.2.2.2).It is necessary that IPsec exited through backup channel.In the settings IPsec local-address 2.2.2.2. The esp traffic goes through the...
View ArticleDHCP on eth1 interface only
I have the er-lite 3.eth0 - WANeth1 - LAN 1 (192.168.10.70)eth2 - LAN 2 (192.168.0.79)LAN 1 is our network. LAN 2 is the network of a company we share our office with which is connected so we can use...
View ArticleIPsec [Strongswan] no traffic routed
Hi, I am trying to setup an ER-X as a road-warrior client via IKEv2 to MS RRAS.Currently the tunnel gets succesfully created but no traffic is getting routed. If I ping the assigned ip [Firewall is...
View ArticleSyslog set to debug, not getting any firewall messages
Any thoughts? Here's my config for syslog set system syslog global facility all level notice set system syslog global facility protocols level debug set system syslog host 10.0.5.30 facility all level...
View ArticleHow do I assign a DHCP server to an interface?
Say I have DHCP1 - 192.168.1.0/24 DHCP2 - 192.168.2.0/24 I want anything connected to eth1 to use DHCP1 and anything connected to eth2 to use DHCP2. I can't seem to find an easy way to do this.
View ArticleOpenVPN static IP for clients
Hi! I recently configured a L2TP VPN with static-ip for some clients. But I'm trying out OpenVPN as well.Is it possible to assign static IPs for clients by name/certificate when using OpenVPN? Didn't...
View ArticleWARNING TIMEOUT: checkip.dyndns.org after 120 seconds
Seeing this message intermittenly in my router log My Dynamic DNS provider is afraid.org, assume that checkip.dyndns.org is used to confirm regardless of the service used. Have no problem accessing...
View ArticleCan't get VPN client access to work (both L2TP/IPSec and PPTP)
I'm at loss getting my PPTP and L2TP/IPSec VPN's to work. I'm running the latest 1.9 firmware on an ERLite, with dual WAN for failover only. I'm trying to set up L2TP/IPSec and PPTP VPN for client...
View ArticleIPSec x509 VPN Setup on ER POE Fails
I want to setup a VPN betwen remote clients and an EdgeRouter POE. I have followed the instructions from an amalgam of references including the UBNT Help Info and third party tutorials including this...
View ArticleIPSEC VPN issues Please Help!!!
I have two EdgeMax lite units. I'm having issues with the site to site ipsec VPN's. I'm depserate for some assistance. One of the units is on 1.9 the other on 1.8. The tunnel will connect just...
View ArticleOSPF or Static Routes. Two Routers + Two Buildings + One WAN
I am working on ramping up my network. Currently we only have one router (in building 1) that performs all L3 duties for both buildings. I'd like to distribute the routing responsibility by installing...
View ArticleAutomate Firmware Update + Configuration
Hello guys, I would like to have your help, I´m kind of new to Ubiquiti equipment, then I need the help from the experts here. I has been reading a lot and cannot find how to do this task. I will...
View Article