ERL Audible Hissing
Picked up an ERL a few weeks ago and have noticed an audible hissing/noise attributed with load on the router. It will make a high pitched hiss and click like sounds (similar to a laptop hard drive),...
View ArticleBlock interface to WAN out
Trying to block access from eth2 to Internet on v1.9.0. Set Intreface Addr (either Network) as eth2 with CLI, but eth2 still able to send packets to Internet. What's wrong? interfaces { ethernet...
View ArticleClik here to view.
NAT problem
ello everyone, im facing a problem with Edgerouter SPF X, i can't make DNAT work. i have try to make it work with the Port Forwarding tab without success Test from external: The edgerouter is very...
View ArticleHook into DHCP
I am trying to have a script run after dhcp gets a new IP/lease on eth0. I tried to place a script into /etc/dhcp/dhclient-eth0-up-hooks.d/, since I oculdn't figure out if I should put it there or in...
View ArticleEdgeRouter Lite QoS setup
I need some solutions to setup QoS on my Ubiquity EdgeRoute Lite-3. This is my configuration.Web - 70%Download - 10%Other - 10%set traffic-policy shaper downloadset traffic-policy shaper download...
View ArticleL2TP VPN Help
Could you please tell me how did you configure your edgerouter for l2tp over ipsec? (v.1.9 here) I've followed the documentation from ubnt and the community, to setup the VPN, but is not working. The...
View ArticleEdgeRouter POE Link Aggregation with EdgeSwitch and Unifi AP
Hi Community,Since Today I'm the proud owner of an ERPOE-5, 2 Unifi AP's and an EdgeSwitch Lite. Now during the setup, a question came up on my head I have a Synology NAS which is connected to my...
View ArticleVIF Removal
Greetings,I have deleted a VIF configuration but it still shows up in the show interfaces commands. The only way I can clear it is to reboot. This is causing a problem with reprovisioning the same...
View ArticleEdgeRouter POE - VLAN HELP!
Hey guys/gals! So, I've been an Ubiquiti user for about 6 years now and everything I've ever touched has been super intuitive...until now! Here's my setup and what I'm trying to accomplish. I'm...
View ArticleIPsec VPN with PSK: IKEv1 works and IKEv2 doesn't? Check id / remote-id
I set up an IPsec VPN with the GUI and (works great) which uses IKEv1 and a pre-shared-secret. I decided to try changing to IKEv2:set vpn ipsec ike-group [group-name-here] key-exchange ikev2but the...
View ArticleWAN to DMZ works - LAN to DMZ doesn't
firewall {all-ping enablebroadcast-ping disableipv6-receive-redirects disableipv6-src-route disableip-src-route disablelog-martians enablename DMZ-to-LAN {default-action dropenable-default-logrule 1...
View ArticleGuide / Tutorial for firewall rules
Hey everyone, I've bought a Edgemax Poe Router to mess around with but now i'm trying to find a guide / turorial on how to make firewall rules(to block and allow).Is there a manual or tutorial for that?
View ArticleEdgerouter X-SFP Not working
Hi all - Question for the masses. I have a new Edgerouter X SFP and it is working great all except one little thing - I can't seem to get the SFP port to behave properly. The setup right now is eth0...
View ArticleConfiguration for 2 WAN IP Blocks
Hi Everyone, I have an issue with setting up my EdgeMax Router to work with 2 WAN IP Blocks from my ISP coming in on one network port (eth0). I currently have the following two blocks:66.81.X.X /27 and...
View ArticleTraffic Analysis/DPI updates "summary"?
I've been tracking the apps in each of the updates for deep packet inspection (logging them). I noticed that the update a couple days ago decreased the total by about 1200 entries. I'm assuming this...
View ArticleClik here to view.
Kernel panic - not syncing--ERL--EdgeOS1.9
After powering off my ERL to prepare it for some wire maintnence, the router is no longer responsive on boot with the following output shown in Console. The first entry reflects a normal boot attempt,...
View ArticleMulti-Site Multi-WAN loadbalancing
Hello together, I am pretty new to the routing business, still some knowledge is there. With my first installation, I am quite amazed how easy loadbalancing and failover can be set up with an ERX. Now...
View ArticleCLI merge cmd details
I've scrounged through the forums and looked at the EdgeMax 1.9 User Guide but can't find any details about the merge command. So some questions: 1) Does merge require a reboot? (Hopefully not) 2) Is...
View ArticleVLAN traffic showing up as parent interface in dashboard and SNMP; normal?
ERL-3: eth2: WAN eth1: LAN eth1.1003: Guest LAN Switch: VID 1003 tagged on ports 1 and 2 Port 1 is ERL-3 eth1, port 2 goes to UAP-AC-PRO UAP-AC-PRO: LAN SSID untagged Guest LAN SSID on VLAN 1003...
View ArticleLoad Balancing
Hi, Currently i have a EdgeRouter Lite (V1.7) set up with 1 WAN and 2 LANS with VPN tunnel running at the moment. Is it possible to convert one of the LANS to WAN? as i'm planning to do a Load...
View Article