Extra Security on Edge Lite Router 3
Hello All, I might be paranoid, but I've been trying to find if there are any vulnerabilities that require closing, or extra security options to enable, on my Edge Lite Router 3. I've followed the...
View ArticleClik here to view.
Problems With New Router Install
Hello everyone, I have a problem I can't seem to get fixed on my own and I hope to get a little help.I just installed a EdgeRouter X to replace a 12 year old router that had finally given up the...
View ArticleRoute tee command in IPChains
I found a post where the ipchains route tee command was not implemented back in 1.7 and was too late to be added to 1.8. Does anyone know if tee was implemented in 1.8.5 or will be added in 1.9? It...
View ArticleDC Power Connectors for EP-R6
Greetings,Looking for the exact terminal connectors for the DC terminals to power an EP-R6 via DC. Saw this awesome post but that is overkill. We just want to run DC voltage up the tower to power the...
View ArticleEdgeMax Lite traffice shape for one client
Hello! I have an EdgeMax Lite (1.8) router.I want to shape upload traffic just for one client (MAC/IP address based traffic shape)The LAN interface is eth1, and the internet is ppoe on eth0How can i do...
View ArticleER-X 1.8.5 PPTP VPN Win7 client troubles
I have followed this guide for a PPTP VPN with local authenication on my ER-X. Setup all seemed to go well, I've added the 2 rules to the WAN_LOACL ruleset (see attached screenie). I can connect with...
View ArticleNeed Help (Dumb Question)
I recently modified my edge router, and added support for IPV6. In the process I added some basic firewall rules. In my haste I issued this command, but put the wrong interface, I added it to my WAN...
View ArticleERLite seems to be limiting my Internet speed, Help please
I have a ER Lite which has worked flawlessly since I got it a few months back. My ISP has provided me with 110 down and 10 up and I get those speeds no problem. Today I upgraded to the new 250mbps...
View ArticleClik here to view.
access control for OpenVPN?
How can I enforce different access control to different VPN groups?vtun0 clients only has access to network a, vtun1 clients can has access to serverort, vtun2 clients cannot talk to each other, vtun4...
View ArticleClik here to view.
How to install a Valid Certificate on the ER (version 1.8.5 and above)
The instructions in this post relate to Edgemax 1.8.5 and above. If you are using 1.7.0 or below, then you will need to use the method set out in this earlier post. The ProblemEdgerouters have a very...
View ArticleER-X not dishing out DHCP
Hello, I just purchased a ER-X and it is not giving off DHCP? What am I doing wrong? I have tried plugging it into internet but nothing, no internet and nothing. I've tried to config my computer nic...
View ArticleClik here to view.
PPTP VPN behind NAT
I have an unconventional setup where I have two Edgerouter Lite operating in my system as such. Fiber Modem > ERL 1 > Powerbeam AC > ERL 2 > Switch. The reason I have the first ERL is...
View ArticleBlock access to ERLite management
Hello again!I'm working on seperating access for my LAN event NOC into VLANs. I have the main vlan, 1 and the Management VLAN, 4. Two of the 3 ports on my ERLite are bonded (for various complicated...
View ArticleUpgrade from 1.7 to 1.8.5 ospf no longer working
Good evening. We had this happen when we reloaded a router at an active site after a dhcp issue, and we are in the process of bring up a new site and figured we would try it on a fresh router without...
View Articleforce load balance back after failover
Hello everybody! Currently I have fw 1.8.0 in one of our ERPoe-5 with failover load balance configured. The main line goes off once a day for an hour o so but apart from that is very stable. the...
View ArticleERLite-3 IPSec VPN throughput issues
Hi all, I have an ERLite-3 that I've connected to AWS via an IPSec VPN. I've followed the AWS-supplied configuration as best I could, but I'm encountering throughput performance issues. When running...
View ArticleERPOE5
I'm sure I'm doing something wrong, but here's the deal: ERPOE:PORT0-NO CONNECTIONPORT1-OFFICE LANPORT2-GUEST WIFIPORT3-IP CAMERA NETWORKPORT4-WAN We are using a 200/20 internet connection, but only...
View ArticleHarmony Universal Remote - intermittent connectivity
Has anyone had success in connecting to a Harmony remote, which seem quite popular? The hub will accept commands from my remote at any time (as it is an IR signal) but when I launch the Harmony app,...
View ArticleedgeOS 1.8.5 | ribd uses much CPU
Hi all! why is ribd using so much CPU? top - 11:08:59 up 22:32, 1 user, load average: 1.19, 1.13, 1.14 Tasks: 79 total, 4 running, 75 sleeping, 0 stopped, 0 zombie %Cpu(s): 19.1 us, 30.4 sy, 0.0 ni,...
View ArticleRestart the DHCP server
ERX 1.8.5 How does one restart the DHCP server without rebooting the router? In some instances I have seen a new DHCP server not become active on an interface for some time, and I would like to know...
View Article