OSPF and failover compatibility
I have three sites, each with an Edgerouter, connected by wireless backhaul like this: A--B--C A - ERPOE 1.7.0B - ERPOE 1.8.0C - ERX 1.8.5 Sites B and C have their own internet connection. I have...
View ArticleProblem Layer 2 VPLS
VPLS on difierent Brands not allowing Crossing traffic on layer 2 All that is Layer 3 when you try to deploy UN service as DHCP or CDP included PPPoE these services is not in The Other Side The test 'm...
View ArticleEdgeOS doesn't check DHCP after an interface change.
I'm running an EdgePoint R6 on 1.8.5 and came across a goofy situation, which has the potential to actually happen a lot. I had a subnet on eth2, and another on eth2.110, which both had a dhcp pool...
View ArticleEdgeRouter PoE5 - Setting up Eth1 and Switch0 to both share WAN (eth0) - New...
Hi,I just got an edgerouter last week and am having trouble setting up the interface for eth1 correctly after hours of combing through posts, guides, etc. Essentially I am trying to have Switch0...
View ArticleKeeping GUI logged in on ER
Is there any simple mechanism to keep the ER GUI logged in? In some environments that is not a security risk (after all, you can keep ssh sessions up indefinitely) and having to keep logging back in...
View ArticleCan't get dual wan failover only to work
I'm trying to setup dual wan, with failover to eth1 only. No balancing needed. Essentially i want both connections to be active, but my LAN should only be connecting to the internet using eth0, except...
View ArticleAllowing IPsec NAT traversal
Testing a config with an ER-X on the inside of an ER-L, creating an IPsec VPN to another (remote) ER-L. If I try to set this up using Port Forwarding (with auto firewall) I get only TCP and UDP options...
View Articleerlite3 dhcp
laptop plugs into eth1. what is stopping laptop from getting ip in range 172.18.0.10-100? ubnt@ubnt:~$ show configurationinterfaces { ethernet eth0 { address 192.168.1.1/24 duplex auto speed auto }...
View Articlel2tp failed to connect, after a couple hours, it worked, and here's the trace...
I've got l2tp working from a windows client to EdgeOS with RASIUS windows server. A few hours ago, it stopped connecting, so I looked at the EdgeOS /var/log/messages log. There were addresses in the...
View ArticlePort Forwarding help when using VLANs and Firewall Rules......
Hello All, so I wanted to add a couple of VLANS, and setup a firewall so that each VLAN cannot communicate to systems on the other VLANS. I got that working, but it would appear I broke my...
View ArticleAnyway to See Failed Service and Restart It
Is there a way to see what services have shutdown/failed and restart them without having to reboot the entire router? I recently had to reboot the modem to get my IPTV working again, if possible I...
View Articleedgerouter 8 Random Reboots
Our new ER-8 is panicing and rebooting randomly with a new configuration on it. We've tried: - Soft/Hard Reset- Re-install v1.8.5 firmware We add a minimal configuration and nothing actually connected...
View ArticleDMZ Rules
I am using Edgerouter poe and I have the wan connected to eth1, the LAN is on eth2 and eth3 (switch 0) and the DMZ is on eth 4 The IP of the router is 172.16.54.26The network of LAN is 10.1.0.0/16The...
View Articleforward 3 separate PPPoE WAN to 3 separate LAN
Im new to the Edge router and I configure the router through the WEB-GUI. The situation is as follows:There is a fiber switch from the ISP that delivers 3 WAN connections. I would like these to be...
View ArticleL2TP over IPsec internal dns resolution
I'm having some trouble with internal dns resolution when using the vpn connection The configuration on the router is as followsconfigure set vpn ipsec ipsec-interfaces interface eth1.2 set vpn ipsec...
View Articlewan to dmz
what is the ruleset and rules that I need to set to allow WAN to access DMZ ??
View ArticleEdgeRouter IPv6 settings for BT Internet
Hi, BT Internet are currently piloting IPv6 to their UK customers. I see reports in other forums of some people getting occassional IPv6 connections with BT Home Hubs. Does anyone know the correct...
View ArticleERLite: Unable to get a /64 on LAN working from /48 supplied by ISP without...
Hello, I have got a /48 from my ISP in our company. I have set up the Network with a /48 netmask on my eth1 interface (uplink) and a /64 subnet from that /48 net on eth0 vlan 1000. I have set up...
View ArticleSimple PP2P VPN Setup
Hi guys. First of all thanks for a great product! I've had simple configuration routers so far. Simple but powerfull like ASUS. Is there any chance you could simplify the process of building a VPN? Is...
View ArticleScenario for interconnecting 2 Unifi's
Noob here.. I have two UniFi's - one operating as a fancy AP , the other still in the box. What I would like to accomplish is to have 3 WiFi networks running seemlessly operating across both UniFi's...
View Article