Set up different DNS servers for different networks
I'm configuring my EdgeRouter Lite to have four networks VPNISPDMZGUESTFor the DNS, I have it set to Forwarding. However, I don't want to have the DNS requests for the VPN connection going out through...
View ArticleCannot access router interface
Hello, I recently bought a EdgeRouter Lite 3 and it works well except that I cannot access the web UI from my PC anymore (I could at the beginning), only from my laptop. If I try to connect from my PC...
View ArticleL2TP VPN with eth0 DHCP IP adresss from ISP
Hi, I am using this tutorial:https://help.ubnt.com/hc/en-us/articles/204950294-EdgeMAX-L2TP-Server At the end I get the following error;l2tp vpn configuration error ipsec did not start Google tells me...
View ArticleNAT Hairpin not working - New EdgeRouter
Hi, Today I'm installing a new EdgeRouter.- Internetconnection is with DHCP- Default wizard WAN+LAN- Configured L2TP VPN- Configured port forwarding NAT Hairpin is not working and is needed ASAP.Can...
View ArticleEgderouter bond failover (mSTP?)
Hi all, I would like to configure an EdgeRouter to have a redundant trunk to two EdgeSwitches. With my regular Linux hosts I just configure two LACP bonds to the two switches which I place into one...
View Articlegetting rid of ssl warning on GUI
I see where under service->gui there is a "ca-file" and "cert-file" setting. However, it is unclear how to use these. I have loaded my cert [*.<domain>] and the ca file into /scripts/config...
View ArticleDNSmasq + traffic analysis = ips?
Hi I have just enabled DNSmasq on my home setup and now Traffic Analysis only shows ip addresses for everything that does not have a static mapping on the DHCP server. As far as i can tell this is...
View ArticleSlow FTTH Speeds
I have 1gig up/down and I'm lucky to get about 130 in either direction. When I had the centurylink router hooked up 950mbps was typical. Offloading is enabled, beyond that I'm not sure what to check....
View ArticleUnreliable Web Connection for VPN Clients
I've setup a L2TP/IPSEC VPN connection with my edgerouter x. When I connection (iphone and android tablet) web traffice is very unreliable. Most webpages will fail to load but some load just fine....
View ArticleEdgerouter Lite with Cox Gigablast
Hello, I am not a power user, but i recently bought the Edgerouter Lite to use with my Cox Gigablast connection. I went through the basic settings shown on the Internet, to make port 0 the WAN port,...
View ArticleEdgeRouter Lite IPSec Passthrough
Hi all - I've recently set up my ERL but am having issues connecting via IPSec from devices behind the router to VPN concentrators on the internet. Specifically, I'm unable to connect to Private...
View ArticleClik here to view.
Do ERLite Support other brand of VoIP?
Hi, i configure EdgeRouter Lite which is connected to the switch, however, I found that the Polycom IP4000 VoIP does not work well. I just follow previous router port forward. The voip is in static ip...
View ArticleEdgeMAX - L2TP Server setup issue - "L2TP VPN configuration error: IPsec did...
Am using this guide...https://help.ubnt.com/hc/en-us/articles/204950294-EdgeMAX-L2TP-Server... to attempt to setup a VPN. I had a previous VPN that worked well, but dissapeared from the config,...
View ArticleVPN Setup on Edgerouter Lite
I'm trying to figure out how to set up PIA VPN on ERL. I tried to follow this: https://www.youtube.com/watch?v=OQHVCqUL6d8 , but when i have vtun0 enabled, I lose internet access from lan clients. I...
View ArticleIssues after switching WAN to dynamic IP
I just switched over from a static IP to a dynamic IP on why WAN interface. Since then I've had a couple of issues I can't resolve. 1) SSH no longer listens on the WAN interface. It works fine on the...
View ArticleOne Way IPSec VPN Traffic with WAN Failover
I've been trying to get this IPSec VPN setup successfully for a while now, but it just got moved up on the priority list. Here is what I have: Main OfficeEdgeRouterPoE - Firmware v1.9.0WAN1 - Cable...
View ArticleEdgeMax -> Toughswitch POE -> UVC G3 = speed problems
Hopefully someone can give me some direction here... I have a setup that is:EdgeMax POE ---1000mbps---> ToughSwitch POE 8 ----100mpbs----> UVC G3 Camera The camera feed is being consumed over...
View ArticleVLAN source routing
I'm trying to understand how vlans can be used on my ERL and am using this as a reference: https://help.ubnt.com/hc/en-us/articles/204952274-EdgeMAX-Policy-based-routing-source-address-based- I don't...
View ArticleER-PoE boot fails with all ports plugged in
Every Timei have a power blip on our hydro lines we end up with an issue of the Edge Router not booting.unless i manually disconnect and re-connect all port cables after 5 minutes of it being booted....
View Articleopenvpn tunnel
I have many tunnel up like this: generate vpn openvpn-key /config/auth/secretClientsudo scp /config/auth/secretClient ubnt@ippublicB:/config/auth/secretClientconfigureset interfaces openvpn vtunXset...
View Article