EdgeRouter X v1.9.0 does not work after reboot
Hello Everyone, I have an EdgeRouter X running v1.9.0 that works great until it is rebooted. After a reboot the router is not accessble on any interface and must be reset. I returned the first...
View ArticleDNAT Mutliple WAN IPs to Internal Servers
I have an external connection with more than 1 IP address. I'm having difficulty working out how to enable port forwarding or DNATing so different external addresses are sent to different...
View Article1 of 3 ipsec tunnels not working properly. Status = up but no traffic
I have 2 ERLs, a USG ,and an ERP. 1 ERL and the USG are connected to the ERP just fine and the VPN is up with traffic traversing it. However, when I use the GUI to set up a 3rd tunnel between 1 ERL and...
View ArticleQuestions with bridging eth1port
I just ordered the ER POE5 to replace an EOL Cisco RV180 router on the first floor of my 2 floor house. I currently have 4 switched 1GB ports on the RV and have the following connectedNAS - no...
View ArticleFull Tunnel VPN
Hi, I am trying to configure an EdgeRouter Lite as a VPN router. I have the VPN connection working to a Cisco ASA, but I can't figure out how to configure the router to route all traffic through the...
View Articleguidance please - EdgeRouter PoE5 - best wireless strategy for small LAN?
Hi. Recently purchased an EdgeRouer Poe5 - it works great. Now I want to add wireless capability to a small home. Are there any speciifc advantages/benefits to going with a Ubiquity AP like the...
View ArticlePort forwarding question
I'm having difficulty understanding this. clive@Southwater-192-168-14-254# show service nat rule 1 { destination { address 192.168.1.13 group { port-group SSH2222 } } inbound-interface eth0...
View ArticleClear Squidguard Log FIles
Is there a way to clear the squidguard log files? I did manage to naviage to the var/log/squid folder and deleted the blacklist.log file. However, after restarting the service and generating a new...
View ArticleMulticast IPTV
So, Edgerouter PoE with BT TV. What's the deal with getting multicast IPTV to work? The YouView box is a couple of switches away from the router. They're HP 'smart' web-managed switches, which...
View ArticleClik here to view.
Very simple BGP config crashes BGP on one ER-X but not others (1.9.0)
I have a bunch of ER-X running a combination of 1.8.0, 1.8.5, and now 1.9.0. They all have an incredibly simple BGP config - the IPs and ASNs are different, but they're otherwise identical....
View Articleheads up Edgerouter 5 POE WAN 2LAN2 wizard
Just a heads up, if you do a WAN2LAN2 wizard and yout internet acces is on a VLAN, after the wizard you will have no internet acces, because for some reason masquerade for WAN is still on ETH0, in...
View ArticleWAN to 2 LAN's
I have two separate subnets as local LAN's(eth0 and eth2) on an ERpro-8. I have 5 public static IP addresses. eth1 is the WAN. I want to run my 207.255.239.50 WAN to my 192.168.50.0 LAN. I had this...
View Articlecan't pull public ip with dhcp on netgear cm600.
Hi. I'm trying to setup my local network with an EdgeRouter Lite and NetGear CM600 on comcast. I'm on the new v1.9.0 firmware. I've tried the basic setup and a with the CLI. I can't seem to pull a...
View ArticleEdge router PoE 5 ports simply stoppped working
Hi All, I'm quite new to Ubiquiti products, so I describe situation and may be someone will be able to help. 1. Purchased one EdgeRouter PoE with 5 ports and one PicoStation M2HP. 2. Connected and...
View ArticleAdvanced Queue by internal port??
Is it possible to set an advanced or basic queue for application port? I'd like to throttle a specific port to a set amount of ingress/egress bandwidth, is this possible?
View ArticleIPSec AH (NOT ESP)?
Hi all: I have an application that requres explicitly AH IPSec tunnel. Its not strictly a VPN, as payload encryption is strictly prohibited. I'm told that I have to use Microtik for this, as EdgeMAX...
View ArticleEdgerouter X enough for my home?
Ya, hoping to keep this straightforward and easy.Right now, trying to figure out which EdgRouter suits my need.What I have (bought/being installed.) (2) UAP AC PRO access points being installed next...
View ArticleERLITE 3 Setup question (prepurchase)
Hello I am about to purchase the ERLITE as I think it will do what I need but I wanted to verify.I have FTTH and where it comes in it needs to be split over to the TV portion and my home LAN portion....
View ArticleEdgeRouter Pro - SQUASHFS error: Unable to read fragment cache / page block
Greetings guys, I have an EdgeRouter Pro which suddenly stopped working. I connected to the Serial port, and I am seeing: SQUASHFS error: squashfs_read_data failed to read block 0x1451786SQUASHFS...
View Articleimq0 imq1 on EdgeRouter 5 PoE
Hello, I want to set few things on EdgeRouter 5 PoE: ip link set imq0 upip link set imq1 up tc qdisc del root dev imq1 2> /dev/nulltc qdisc del root dev imq0 2> /dev/null..and etc. etc. imq0 -...
View Article