PBR + Timeslots
Hey guys, short question, is it possible to have PBR with timeslots? PBR is already implemented but for certain VLANs i want it just for certain timeslots. Reason: Sitting on Fibre + Cable and i want...
View ArticleDHCP server always gives out address from .38
I have an ERL 3 running 1.9.0. I have WAN on eth0 and LAN on eth1, with a DHCP server enabed on eth1. eth2 is a LAN but is unsed (DHCP server is disabled). I used one of the wizards to create this...
View ArticleHowto: Use an ER-X as VPN Remote Access Server (IKEv1 + PSK)
Hi, Fisrst of all, I want to say that I am not an expert on Strongswan or Debian. I am not able to help you on debug or troubleshouting this configuration. Sorry ! Recently Apple decide to remove the...
View ArticleCannot hit the webGUI on ER-X running 1.9.0
Configured the router through the webGUI a couple weeks ago and all was well. Went back to do a little more work and I can't hit the WebGUI. I can SSH in and I pulled the config. I have attached it. I...
View ArticleHaving Trouble with Enable Hairpin Nat
Hello all,I have been having trouble forwarding my port 80 to my Snyology NAS webserver. I finally got it to work and can successfully navigate to the external IP from outside my network. However,...
View ArticleEdge Router -> Cisco Switch (IP unreachable) VLAN Issue?
I am getting unusual problem with the interfaces of the Edge Router and Cisco Switch. VLAN Interface on the switch is UP and ports are UP. However, I cannot ping 192.168.1.1 from the switch and...
View ArticleHow to bind two LAN ethernet ports?
Hi, I have two bridge that will be connected to edge router.What should I do to ensure that the two ethernet ports can reach each other? Bridge 1: 192.168.0.0/30Bridge 2: 192.168.0.4/30 Please help.
View ArticleFirewall Routing Configuration suggestion - Guest Network and Security Cameras
Hello all. I am trying to setup the following and having some issues. The different ways I have tried firewalling this off is not working, so I thought I would ask for suggestions. I Have a...
View Articleconnect my new edgeswitch lite to edgerouter or pfsense?
Hello All.. I think I have looked at too many youtube videos. I an purchasing an edgeswitch lite (24 port) and am very excited.I watched a ew videos on the edgewsitch with POE passthrough and thought...
View ArticleEdgeRouter PPPoE configuration help
Hi All Just got an EdgeRouter X and I want to configure it for PPPoE, and I need help. Can some one point me to a simple set of instructions to set it up. Thanks.
View Articledns resolution problem with dual-wan failover
Hello everyone, I have a problem trying to setup following configuration (edge router pro, 1.9.0) - I used the wizard "Load Balancing" to setup basic failover scenario: eth0-192.168.1.1(lan) --->...
View ArticleWhy I cant download files using cURL? Works only from ubnt site ...
Hello boys, I`m trying to download a file into my ERPro, If I try download from another host that isnt dl.ubnt.com the download even start. radionet@BORDA-BGP:~$ curl -vL -o teste.teste...
View ArticleCommands to Help Troubleshoot Routing/Policies
Are there any commands to help with debugging routing and policies? An example, My pings are not going through to host A. On a fortigate I can use the "diag debug" with a filter for the ip and it...
View ArticleLoad Balancing / Dual WAN with two static IP
Hello, I have an existing network setup I want to upgrade, as in replace the existing load balancer. I can't change the config of the modems, so, I have : 192.168.2.253 on eth1192.168.1.253 on eth0 My...
View ArticleTwo WAN means no Internet
Same issue as another thread that the OP has marked as solved. Config created from the load balance template, then created VLANs, and then found load internet access broken if both WANs plugged in....
View ArticleFirmware ugrade without internet connection (local file)
Hi Is it possible to upgrade the firmware if i have the firmware files (1,9) local on my MAC, but no internet connection? Thank You Mathias Kehlet
View ArticlePSA: Sweet32 vulnerability in Blowfish (BF-CBC) OpenVPN default encryption
If you're using OpenVPN site-to-site with the default BF-CBC cipher and pre-shared-key mode you should probably change to AES-128-CBC. Use set interfaces openvpn vtun# encryption aes128Don't forget to...
View ArticleRedirect subdomain to internal IP
Hello All, I would like to assign some domains to some internal servers that I have running. I own a proper domain name and was hoping I could use subdomains off of it to redirect to my internal...
View ArticleClik here to view.
PPPoE server problems
The EdgePoint 6 Port's implimentation of PPPoE has been a nightmare for us and we are reaching our deadline. For some reason, anyone with Apple brand routers can not PPPoE in and neither can...what...
View ArticleNo DHCP on VLAN 10 for guest network
Hello, Im using a Edgerouter X on 1.90 and ive set a DHCP for the 192.168.3.1 network and tagged it 10. Im usng a Unifi AP with the guest network set to vlan 10 and it doesnt work as I get a 169...
View Article