Port forwarding problem
Hey folks, I just picked up an ER-X to replace my router that's getting flaky, and I'm embarrased to admit I can't get port forwarding to work. I have a little web server sitting behind the router that...
View ArticleClik here to view.
New Small Enterprise/SOHO: UniFi AP - no Internet with Edgeswitch &...
Newbie here setting up a small enterprise / SOHO system with an EdgeRouter Lite, EdgeSwitch 24 PoE and UniFi AP-AC. I followed the EdgeMAX - VLAN Walkthrough with EdgeSwitch using Sample Enterprise...
View ArticleClik here to view.
dhcp 2 3 and 4 server not give out ip
Hi, I am new to EdgeOS and ubiquity itself. I just receive my router edge pro " EdgeRouter Prov1.9.0 " and update its firmware to latest one. It took me awhile to get it up and run. However, I...
View ArticleEdgerouter X is it possible to setup with multiple vlan?
I would like to do the following with the edgerouter x https://help.ubnt.com/hc/en-us/articles/205197630-EdgeMAX-VLAN-Walkthrough-with-EdgeSwitch-using-Sample-Enterprise-Topology Is this possible? eth0...
View ArticleISP IPTV -> EdgeRouter-X -> UAP-AC-Lite Wireless VLAN
Hello I get both internet access and IPTV from my swedish ISP Telia. If I understand everything correct the internet isn't connected to any VLAN but the IPTV is connected to the VLAN 845. My setup...
View ArticleIPTV setup help
I have the EdgeRouter-X and trying to get it to work with my ISP IPTV. My Asus router I can setup so that incoming VLAN 845 from my ISP redirects to port 4. On port 4 on the Asus router I connect my...
View ArticleLoad Balance and Speed Test
Hi guys,I finally got the load balancing to work with 3 wans.1 on eth0 - ISP1 - 50 Mbps1 on eth1 - ISP2 - 50 Mbos1 on eth2 - set to failover only - 10 MbpsProblem is internet breakout is very slow;...
View ArticleHow to set up firewall rule for blocking port for specific device
Hi all, Got some info here about blocking ports, and for the most part it worked. I set up a firewall ruleset that accepted in/out, then in it I added a rule that was set to all protocols (or tcp/udp),...
View ArticleHelp for Choosing Equipment
New to the forums and new UBNT user. I was unsatisified with consumer router/AP solutions and lack of performance. I found UBNT and decided to purchase an EdgeRouter Pro-8 (Because I wanted to mount it...
View ArticleERPoe-5 + UniFi AP port speed issues
Hi there. My network looks like this: internet (about 70-80Mps both sides) comes to eth0 port, unifi ap wired to eth1 port (poe 24v). Out-of-the-box Unifi AP said that it's "connected" in UniFi...
View ArticleClik here to view.
Two WANs with dynamic IPs and two LANs
I've been banging my head on this for a few days and I can't seam to find a solution fo it. This is my setup:I'm using an EdgeRouter LiteEdgeMAX - Policy-based routing (source address based)I've used...
View ArticlePort forwareding on an ERPOE-5 - external port different than internal
So I have been pounding my head on my desk because I just can't figure this out. I want to route port 32888 externally to port 80 internally. I am able to get port 80 to port 80 working fine but I am...
View ArticleLoad Balance Test Script
New ISP installed and added to a load balance group. However the ISP has terrible letancy issues (satellite) and I would like that connection to be dropped from the group when the latency becomes too...
View ArticleRedirect subdomain to internal IP and Port
Hello,I'm looking to redirect different subdomains to different ports on my server but I'm running into a bit of an issue with the port 80 to 443 automatic redirect. What I'm trying to acheive is:...
View ArticleBrand new Edgerouter Lite won't issue DHCP
Hi Folks, I'm trying to access my new Edgerouter Lite (ER-Lite 3). I'm plugged into eth1 with my MacBook Pro. I have a solid green on the console port and mostly solid green with occasional blinking on...
View ArticleEdgeMax unable to block StreamingMedia
Hello, I have an EdgeRouter-X with firmware 1.9.0 installed on it. Recently my son's Chromebook that he received from school has QUIC enabled on it. As a result, the Firewall Policy that I have set up...
View ArticleCan't access Edgerouter PoE-5- crashed
Tonight, after I create a VLan, during the process of saving it, the router booted me out and now I can't access it. I have it setup as: eth0-WAN, eth1-PoE(AP AC-Pro), rest part of switch0. I don't...
View ArticleClik here to view.
2 IPSEC VTI 2 tunnels through NAT - can it work?
Hi Everyone - I have started playing around with a configuration 'in the lab' to do this, but one thing I can't easily simulate (and don't fully understand, to be honest) is whether what I am trying in...
View ArticleEdgeRouter Lite (apparently) dead, console port green LED is flashing
Hi all, What does it mean when the console port green LED is flashing at power-up? Symptoms:Console port green LED is flashing (no cable connected)eth1/2 have cables connected, but LEDs are off"the...
View Article[BUG] pppoe0 / SNMP ID
I think i've found a bug regarding pppoe sessions and snmp (v2c). Once the pppoe-session gets terminated by the provider and reestablished, snmp recognized the new session as new identifier. So if...
View Article