Can anyone help me figure out how to get eth3 to use the 1gig speed?
So far I have read thta i needed to manully configue it in the CLI. I used teh follwing string but all it did was turn off the port entirerly. What am I missing? "sudo ethtool -s eth3 autoneg off speed...
View ArticleArsTechnica 'Router Rumble'
ArsTechnica did a roundup of some router options. They included two Ubiquiti routers, the EdgeRouter Pro, and the UniFi Security Gateway. It already got mentioned in the UniFi forum (see: forum...
View ArticleEdgePoint R6 - faulty?
We have 3 x EdgePoint R6 units acting as outdoor switches not router.1st of the units has 4 x RocketAC PRISM radios and the EdgePoint constantly turning on and off the PoE ports, and reboots itself....
View ArticleIpSec S2S working on Firmware 1.85 - broken on 1.90
I have an ErLite3 and ER8. There was an IpSec tunnel established and working since install across Firmwares 1.8x. I upgraded both endpoints to 1.90 and noticed the Tunnel not up. After a lot of...
View Articleupnp2 edgerouterX
Hello everyone! I am trying to get upnp2 working on my edgerouterX, but I could use some guidance. My setup: eth0 = 192.168.1.1/24 (this is where all of my wired devices reside)eth1 = where my internet...
View ArticleConfiguring 4WAN 1LAN Load Balancing
I am using Edgerouter PoE5, upgraded to ver 1.9. my internet is using pppoe and internet is on vlan. below is my manual configeth0 - WAN1 (primary)eth1 - WAN2 (backup)eht2 - WAN3eth3 - WAN4 eht4 - LAN...
View ArticleHow to record persistent (eg monthly) individual client bandwidth/DPI stats?
Hi all,May I have some pointer on how to have access to persistent (eg weekly, monthly) individual client usage stats (total up/download, and if possible type of connections like DPI)? So that I can...
View ArticleNPS Radius Edgerouter L2TP VPN NAS Port type
Hi all, I've read through other posts about people trying to get Radius working on their edgerouter talking to a MS Server 2012 R2 NPS service. I have it all talking to NPS with the settings other...
View ArticleEdgerouter lite site-to-site IPSEC NetBIOS name service broadcasts
HiI have 2 sites connected using an IPSEC site-to-site vpn, both sites are on differing subnets (192.168.10.0/24 and 192.168.11.0/24)They're both small windows networks that are just part of a...
View Articleipv6 log message help
Can someone please explain what the following message means:and its implications:Sep 20 17:18:10 stargate radvd[13732]: no auto-selected prefix on interface eth1, disabling advertisements Sep 20...
View ArticleMigrate Network to Lager IP Pool
Please help me out and let me know if there is a better way to accomplish what I would like to. We have an old network with quite a few static IP devices and an hold windows server that is barely used....
View ArticleErpoe-5 Freeze - v.1.60
Hi all,I have a Erpoe-5 with 1.6 firmware. Here is services that i use :- Eth0 : PPoe Server- Eth1 : Internet WAN- Eth2-4 : switch- DHCP- VPN site to site between another Erpoe-5 Regularly(1 times...
View Articleedgerouter lite very high cpu load when downloading @ 200mbit
Hey, edgerouter lite with firmware 1.9.0 eth0 - wan (gbit to modem, 200/10mbit internet connection)eth1 - lan1, no dhcp, no dnseth2 - lan2 (guest, untagged), dhcp and dnseth2.6 - temporary vlan...
View ArticleEdge Router X port forwarding issue...
I have a strange issue and i can't seem to correct it. Running FW 1.9, i have port fowarded 4 ports, 41794, 41795, 4000 and 554, all are TPC. What doesn't make sense is that 4000 and 554 are not...
View ArticleEdgerouter Pro - WAN failover not working properly
I have an EdgeRouter Pro that I am setting up for dual wan with failover. PrimaryISP should be used always when it is working - DHCP (192.168.200.0/24 network in test environment)SecondaryISP should...
View ArticleOpenSSH Vulnerabilities
In order to meet PCI compliance the following vulnerabilities must be addressed in EdgeMAX v1.9CVE 2015-5600CVE 2015-5352 (EDIT: corrected CVE)I couldn't find any information that these were addressed...
View ArticleNo-IP for DDNS
Hello everyone, Can someone explain to me if I can use no-ip as ddns on an edgemax spf. I do not have the router installed yet and I can not remember if this is available service on the router. Thanks!
View ArticleWOL inside LAN not possible with Ubiquiti EdgeRouter POE?
I recently replaced my E3000 router into the Ubiquiti EdgeRouter POE.I love the product, but got 1 problem I can't solve out or find anything about on Google... In the past (with my old E3000) router,...
View ArticleL2tp IPSec offloading is not working.
Hii have vpn users who connecting whit iPhone'sNow I setup a l2tp IPSec vpn and set all vpn and IPSec offload options to enable.But the ERL Poe is running CPU 100%
View ArticleDNSMasq as DHCP + iPXE + TFTP + Options Not Working
My ERL is running 1.9.0 and I want to set up a TFTP server to PXE boot. My FreeNAS has the TFTP server and that is working exactly as expected. It is serving up a iPXE file so I can bootstrap old PXE...
View Article