Edge Router X Automatic WAN failover not working
I have the newest firmware v1.0.9 on a EdgeRouter X SFP. I have used the wizard to set up automatic WAN fail over but can't seem to actually get it working. It is set to do failover only. My setup is...
View ArticleQoS traffic-shaper bandwith allocation
Hello all, I have seen many posts concerning QoS for services (including VoIP) and have following this link to set it up on our EdgeRouter Lite. I have a question concerning bandwidth allocation for a...
View ArticleClik here to view.
EdgeRouter to ToughSwitch Trunk and Network Design
Hello, I am impementing a new and improved network before I go back to school in September... So I need you network design guru's help with this I spent some time trying to configure VLANs between...
View Articlehow to setup my wireless APs
I recently setup my EdgeRouter Lite with a basic config and I had some questions before I tackle my wireless access points. Apologies in advance, I'm not a network guy, I'm trying to learn as I go. I...
View ArticleHow up to date are KB articles ?
For instance, this one has a recent date stamp of 15 aug 2016..... whereas screenshot shows software version 1.6.0
View ArticleClik here to view.
Advanced Queue - can't get it working
Hi, I want to replace my traffic shapers by the use of advanced queues ... but hence the lack of a really good fundamental documentation I can't get it working properly. I even fail with the basics My...
View ArticleQoS advanced queue
Hi, I try to configure a advanced queue QoS on my ERL-3.This is my current configuration : branch { queue 10 { bandwidth 10mbit description Download parent 1 } queue 20 { bandwidth 1mbit description...
View ArticleIPSec site to site VPN using vti interfaces with one router behind a NAT
Hi, We are currently trying to configure a site to site ipsec vpn using vti interfaces.The routers we are using are an edgerouter pro v1.8.5 and edgerouter lite v1.9. Now the edgerouter lite is behind...
View ArticleER eth to bridge
we have a phone vendor needing one of the IPs from our /29. Rather than let the SIP traffic get handled by the edgerouter, we set up a bridge group for the WAN br1 has the wan IP of the edgeroutereth2...
View Articleconfigure wan connection with vlan and masquerad
I would like to know how to configure properly a WAN connection with VLAN and masquerading ?
View ArticleWhich router for gigabit fiber?
Hi everyone! I'm moving flat in a few weeks and the new location is in the coverage zone for a Tier2 ISP that has cabled the flats in the building with 1Gb/s symetric single-mode fiber.They do very...
View ArticleNeed to block subnet from internal to external
I am new to ubiquiti routers but I am now working for a company that has deployed several of these to businesses. I have one customer who is getting messages from their ISP about some high traffic...
View ArticleClik here to view.
Advanced Queue - FQDel and HFQ in the same branch?
Hi, I've rewritten my QoS from Traffic Shaping to Advanced Queue. It took a quite long time to see that traffic limiting seems not to work with FQDel, so I needed to use HFQ for this. I mostly took...
View ArticleERLite-3 V1.9.0 update broke my static routing across openvpn site-site
I have a three site network all with ERLite-3 connected using OpenVPN site-to-site. I updated one remote site first to 1.9.0 and after I did that, my remote site router could no longer ping...
View ArticleEdgeMAX - Automatic WAN Failover with a catch...
I understand that I can setup auto failover, but I am unsure it will work with my current config... Without getting into too much detail yet, the basic question is this... 1) ISP1 comes into Router1...
View ArticleDNSMasq DNS Not Working
I am trying to enable the new DNSMasq but whenver I do, I loose all DNS (internal and external). Below is my config WITH DNSMasq enabled, can anyone tell me whats wrong? Also, when I type "Show dns...
View ArticleLimiting bandwidth for interface that are in switch mode, between those...
Hi, Edgeroute X here !!We configured the ports in switch mode.We want to limit bandwidth between the switch ports.It only seem to work between ports vs WAN. Any advice ? ThanksMathieu
View ArticleAccess eth1 (Lan) from eth0 (Lan)
Good evening, I have the feeling this will be very easy to answer but I am currently missing something in my EdgeRouter Lite setup / configuration. Particularly I have my LAN connected via the eth0...
View ArticleEdgeRouter Pro + AirFiber
Hi, I've have an ongoing issue with my EdgeRouter, but a new twist has appeared with the deployment of an AirFiber. The new issue is as follows: EdgeRouter has 2 relevant ports. One is x.x.x.x/30 to...
View ArticleDHCPv6-PD... server?
I've got a multi-unit location that I want to setup where each space can request their own IPv6 prefix. How would I configure an edgerouter to act as a DHCPv6-PD server? Is it even possible?
View Article