EdgeRouter Firewall Help
I just recently got an EdgeRouter Max to add to a site where we have exisiting UBQ WAPS. I was able to get the wan/lan/vlan/dhcp etc etc going. However I am really struggling to understand the...
View ArticleEdgeRouter X compared to consumer routers?
Evening all, I am upgrading my entire home network and am trying to get a new router. My home internet is cable with 80Mb/s down and 20Mb/s up over coaxial. I'm currently viewing the EdgeRouter X / SFP...
View ArticleRogue Device on Network
I was looking at the DHCP client list last night, and I noticed a device that I didn't recognize. It listed its host name as android-<mac addrress>. I don't have any android devices. I did not...
View Article"Framed-Route" Attribute support
I know that this attribute has been requested here and I was wondering if there has been any update on it or plans to add it and/or other attributes?
View ArticleERL not routing IPv6 correctly
Hi,it seems that I have run into an odd problem that I quite can't figure out.I have a static ipv6 given from my ISP. 2a02:118:12c:9::2/64The gateway is: 2a02:118:12c:9::1 I have created the following:...
View ArticleNetflow setup and guidance
Hello, I'd like to start using Netflow for traffic analysis and capture the data for future review if necessary. Some of the collectors I checked into are quite expensive. Are there any free options...
View ArticleEdgerouter x-sfp and vlan tagging
Hi All, New user of Ubnt-equipment here. I've got little experience with routers and switches outside of the consumer arena.Now I've got a Edgerouter X sfp, and I'm trying to make it the only box I...
View ArticleEdgeRouter isn't routing between interfaces
I am fairly new to personal networking and I am having an issue with my EdgeRouter. I used the WAN+2LAN2 wizard to set up my router and from the CLI I can ping both 8.8.8.8 on WAN and a client on one...
View ArticleDMZ for Nettalk voip
I need to set up a DMZ for a nettalk voip. According to the nettalk instructions I need to put the IP address of the nettalk into the router's DMZ. Currently, the nettalk is on a dynamic IP. Do I...
View ArticleClik here to view.
Dual WAN Policy Based Routing
I have an Edge Router X and would like to configure the following. I have run through the Policy Based Routing article on the UBNT site but haven't been able to get this to work how I want. I have two...
View ArticleUnable to get Internet on ETH1. New setup
Hey everyone, I just got the EdgeRouter Lite and I setup using the wizard. I used WAN+2LAN2... I have internet plugged into ETH0, and unmanaged switch(about 10 clients) into ETH1 and a Ubiquiti...
View ArticlePort forwarding issues
Hi all, I am fairly new to commercial grade routers and recently my company swop out our comsumer grade wireless router to an edgerouter poe5 + AP. After successfully getting our internet up, the next...
View ArticleLocal DNS
Any way to set up a local DNS record so that accessing the plex server is more user-friendly? For example http://plex.local instead of http://192.168.3.4/32400/web?
View ArticleBroadcasting IoT services across VLANs
Hi I have now got a seperate VLAN for my IoT devices, they are running as expected on this LAN and can call home etc I have blocked everything on this network to/from my LAN so to be sure the network...
View ArticleCopy config from EdgeMax to EdgeMax Lite
Hello, Can I make a backup of my EdgeMax config and restore it to 3 other EdgeMax Lite devicesand only change the LAN IP, WAN IP and VPN settings? The 3 new boxes should have the same settings with...
View ArticleEdge Router Pro as endpoint for a dark fibre
Hello, I am about to get a dark fibre. Since I would like to use an edge router pro at our end I would like to know if some knows if this optic...
View Articlesubnet isolation
i have ubiquity edgerouter-x. i have updated to 1.8.5 and run the wan+2lan2 wizard with 'use only one lan' unchecked.i find that i can log in to eth1 thru eth4 as 192.168.1.1.i expected to have use...
View ArticleClik here to view.
1 to 1 NAT and Mail forwarding scenario challenge
Hello,I have a problem with configuring port forwarding and forwarding port 25 to an specific server box.Here's the scenario (IPs are not real and used for example): I have an EdgeMax router eth0 - LAN...
View ArticleSeparate traffic from different ports on a Edgerouter lite
Hello All. I want to preface that I have spent about 3 hours researching this forum and seveal others before asking this question and cant find an exact answer. I am going to provide links to what I...
View ArticleQuestion for L2TP Client Pool Subnet
I am wondering how I configure the remote client to exist exclusively in the same subnet as my LAN. I am currently setup as IPSEC/L2TP. ex. Client IP Pool Start/End 10.33.33.33-10.33.33.40 LAN DHCP...
View Article