DPI - Netflix shows up as 'Web-Other'
1.8.5, verified I had updated signatures, and when streaming Netflix video, DPI shows this traffic as Web - Other, not under streaming media, so I'm not able to shape it anymore.
View ArticleRule faild
Hello, eth0 Interneteth1 Lan88eth2 Lan33 Rule Set eth2 outDEFAULT - Droprule 1 -action ACCEPT source eth2 des 88.40 rule 2 - action ACCept source eth2 des eth0 i can not ping vom 33.55 to 88.40 and i...
View ArticleVPN failing, Win 2012 R2 Radius server
Help, Need debug pointers/tips/hints.... vpn configuration listed below. Trying to get VPN working. I have Win 2012 NPS configured, but not sure if its right... Win 2012 R2 server is at...
View ArticleEdgeRouter X SFP never came back after reboot
I just rebooted my X SFP router and it never came back. walked through a hard reset and am trying to start over, but no connectivity to 192.168.1.1 on eth0. my laptop has an IP of 192.168.1.2 set...
View ArticlePolicy Based Routing support for router-originated traffic
I think a number of problems people report in the forums can be traced to a lack of PBR support for traffic that originates from the router itself. Is this a planned feature? Problems that seem related...
View ArticleER-Pro BGP process lockup
Hi,I just had an ER-Pro running 1.8.5 where the bgp process just died or something.The ER-Pro registered the following: Jul 25 20:56:04 vel1 kernel: eth0: 1000 Mbps Full duplex, port 16 Jul 25 20:56:02...
View ArticleMarking (Coloring) Traffic for DSCP Values for 802.1p
Hello, I am wanting to match traffic on an input interface of a router and mark it with a DSCP value. Once the traffic is marked I then would like to match it on an egress port and prioritize it with...
View Article/config/scripts/post-config.d doesn't work
Recently I created the file: /config/scripts/post-config.d/disable-martians-logging containing: echo "0" > /proc/sys/net/ipv4/conf/all/log_martians and with mode 755, to prevent logging of these...
View Article/31 and /30 routing
Hey Guys, We are getting a new fibre connection installed and it comes with a whole loads of headache of the ISP not listening to our requirements. we are a NGO and have very basic requirements and...
View Article(network.c.543) SSL: couldn't read X509 certificate from...
I attempted to install a Let's Encrypt certificate as shown here: https://github.com/photinus/ubnt-letsencrypt After attempting to install, I am receiving the error mentioned in the title. I also can't...
View ArticleNot able to get IPsec VPN up - what are the troubleshootng steps?
Hi, I am trying to setup a site to site IPsec VPN between two ER (one Pro 8 and one Lite). While I had the VPN up rather quickly and was trying to get traffic running (here), it seems that I'm not even...
View ArticleConfiguring 2 subnets from /29 on ERL-3
My ISP has assigned me a single /29 subnet. That gives me 5 usable IPs. I need 2 subnets so as to segment HOME and OFFICE lans. Tried to get my isp to reassign me two /30 subnets, but they refuse....
View ArticleIPv6 mystery
IP6 was working, but now my network clients are no longer receiving IP6 addresses / DNS server info from DHCP. I've compared my config to others posted, but can't see anything wrong. Any help would...
View ArticleEdgerouter Lite crashed and reset?
Hello Ubiquiti, I have an EdgeRouter Lite that was set up for the longest time with 2 ISP's connected thru the Load Balancing Wizard. Everything was working fine until I got new software that requires...
View ArticleIPsec Site-to-Site routing
Both sites running 1.8.5, configured site-to-site using GUI. Tunnel is up, I can ping both LAN addresses, and I have access to both routers via SSH or GUI. I feel like I'm missing something obvious...
View ArticleNeed help setting up bandwitdh limits per IP base
Hi guy's i need help setting up a trafic shaper targeted to ip. I saw some guides alredy but I need help with the cli of the edgerouter. I am using a edgemax er3 lite (v 1.8.5.) I have experiance with...
View ArticleSetup portforwarding for two interfaces - at once?
Is it poissble to somehow group eth0 and eth1´s portforwarding rules? As it is right now, i have to make 1 portforward rule for eth0, then copy that rule to make a identical rule for eth1.I can see...
View ArticleNote on Android IPv6 with SLAAC
This is not so much as a bug on with EdgeOS but may save some poor soul major time on troubleshooting Android with IPv6 problems..... And MAJOR NOTE TO SELF:On Android 5/6 machines.1) They take SLAAC...
View ArticleEdge router X for IPTV (telia)
Hallo,I'm new to the edgerouter and got one to replace my telia router (thomson TG789n) the problem is that I have my TV over IPTV and telia do this by using VLAN 845 so what i would like to do is tag...
View ArticleHow to connect to a different subnet based on the wireless ssid and not the...
Hello, I would like to know if the following setup is possible, and if it is, how to do it. Here is the situation: 2 interfaces with 2 subnets.ETH1 -> 192.168.1.XETH2 -> 192.168.2.X2 AP:APX ->...
View Article