EdgeMax freaks out after adding another WAN to it
Hello, Yesterday I had my setup running fine with some additional IPSec VPNs to 3 watchguards. Today I configured everything for the second WAN mainly used for RDP to reduce downtime during the switch....
View ArticleERPro - SOHO config - Cannot access Internet
Sorry if this has been covered, but I have an Edge Router Pro that I am trying to configure for a simple SOHO installation. I tried both SOHO wizards. I cannot get anything to traverse from the LAN...
View ArticleHow do you disable a specific IPSEC VPN without deleting it?
I don't see a disable option on a site-to-site level from cli. Thanks
View Articleiproute2 on EdgeMAX v1.8.5beta2
My apt-sources.list looks thusly: deb http://http.us.debian.org/debian wheezy main contrib non-free # wheezy # deb http://http.us.debian.org/debian wheezy-backports main # wheezy-backports # deb...
View ArticleER-X 1.8.5 traffic-policy limiter issue
We recently updated to 1.8.5 from 1.7 and we are having issues applying the limiter to an interface. It is a member of the switch, and I can apply an outbound rate-control policy without any issue. I...
View ArticleState invalid in outgoing rules (WAN_OUT)
Hi all, I'm new to these forums having just purchased an ERL-3, and must say I'm impressed. Eth0 is WANEth1 is LANEth2 is LAN I've set up some outbound firewall rules WAN_OUT to block some specific...
View Articleroute applications to certain ip?
Hallo Guys i looked at the wiki i saw you can route certain ports to certain ips...https://help.ubnt.com/hc/en-us/articles/205223470-EdgeMAX-Policy-based-routing-for-destination-port when i went into...
View ArticleClik here to view.
Firewall questions
I have an edgerouter and an edgeswitch lite 48. I have two networks. One is 10.0.0.0/16 and the other is 192.168.1.0/24. The 192 network is a guest network that is on vlan 33. I have a firewall rule...
View ArticleClik here to view.
Web GUI calculation of ram on ER-X-SFP
I have an ER-X-SFP on 1.8.5 and have noticed that the Web GUI indicates only 36% of RAM is in use; however if i run the command: topI get the following results:top - 16:27:10 up 8 days, 18:12, 3 users,...
View ArticleInconsistant Load Balance Performance
Hi There... I have been running 1.8.5a1 for a while, and had no issues with the load balance I have set up. A few days ago, I loaded the release 1.8.5 and have since then found the load balance seems...
View ArticleClik here to view.
Web Gui empty
Hello, My routeur is up and running, working fine. But when I log in into the admin portal I have an empty page like in my screenshotRunning latest version v1.8.5, connected through Wifi / Unifi AC PRO...
View ArticleChange config by scripts "locks out" manual config: "Set failed"
Each time a scripts ran that altered my config, I'm locked out of further CLI changes to config. I'm trying to change distance on a route, this blocks all future CLI changes. Can't even change...
View ArticleClik here to view.
Problem compiling sslh after upgrade to v1.8.5
I was expecting to have to reinstall sslh after upgrading to EdgeOS v1.8.5, but I've got stuck. I installed what I think are the pre-requisites:sudo apt-get updatesudo apt-get install make...
View ArticleER-8 eth0 disappears after upgrading from v1.8.0 to v1.8.5
I just upgraded a new ER-8 to v1.8.5 from v1.8.0. eth0 disappeared from the config. It was not listed in the Config Tree or the Dashboard. eth1 thru eth7 are the only ones shown. Eth0 is the primary...
View ArticleWeb server is slow behind edgerouter lite
I just got my new Edgerouter Lite 3 and after some getting used to, I got it configured for my network. Everything is working as expected except for two issues. eth0 WAN - dhcpeth1 LAN -...
View ArticleHome lab setup
I am trying to set up the EdgeRouter ERLite‑3 for my home lab.I want to have a separate subnet that I will have a windows DHCP server in to provide addresses for a test VDI lab using 10.0.2.x/24.My...
View ArticleSecond Switch at Edgerouter x-SFP
I use a Edgerouter X-SFP (Firmware 1.8.5) and will connect my Exchange-Server with a public-IP. Here is my description: Public-IP: 92.50.10.114/29Privat-IP: 172.16.1.0/24 I try to create a switch for...
View ArticleDNS stats?
Is there a good way to do DNS accounting on edgemax? I would like to see top queries/errors and full DNS query log for all DNS traffic, even if client changes its DNS server.
View ArticleMonitor Monthly Data Usage
I am a new home user of an Ubiquiti EdgeRouter Lite running version 1.8.5 firmware in the 1WAN + 2LAN configuration. Is there a straight forward way monitor the data usage flowing over the WAN port....
View ArticleHow do I keep 2 LANs isolated?
I am a new home user of an Ubiquiti EdgeRouter Lite running version 1.8.5 firmware in the 1WAN + 2LAN configuration. Is there a way to prevent access between the two "sub-LANs"? Right now, I can ping...
View Article