error logs authentication failure and host name not found
Hello, I consistantly get these errors and I don't know what to do. May 31 16:13:01 edge CRON[12677]: Authentication failureMay 31 16:13:01 edge CRON[12677]: pam_unix(cron:account): could not identify...
View ArticleOdd Routing Issue
I replaced a cisco router that had a simple router. route 10.10.74.0 255.255.255.0 10.10.70.250 Everything worked fine, now that I have an Edge Router POE in place, we can only get pings to route. The...
View ArticleERL connecting two subnets to wan (one subnet under control of cable router)
Folks Our local cable company uses Meraki AP's and locks the configuration to thier Hitron modem/router They NAT out on 192.168.0.x with a gateway of 192.168.0.1 and this is a fixed non user modifiabe...
View ArticleReplacing Stock Fans in an ERPro-8 and ES-24-250W
Hello, I just purchased a ERPro-8 and ES-24-250W for a small home office environment. The ERPro-8 has v1.8.0 of EdgeOS and the ES-24-250W has v1.3.0.4831995. I am trying to quiet the units down as...
View ArticleClik here to view.
Question regarding WAN and LAN VLANs on same physical port
I have a TWC Arris device in my garage with an uplink to my master bedroom closet where the EdgeRouter POE 5 is connected to eth0. I'm getting solar this week (SolarEdge inverter) which will be in the...
View ArticleER Pro Frustration
Trying to setup a erpro8 but am not having much luck . I have the router connected to a edgswitch 24 which i had no problems configuring but the router is a bit advanced for someone who has only setup...
View ArticleDNS and WiFi weirdness - need help troubleshooting
Hey everyone. Starting on Monday, my network has been experiencing some weird issues. The problems seem unrelated, except they all started cropping up at once after 2 weeks of smooth sailing. Hoping...
View Articlechoose router 2 wan 1 lan
Hello, need assistance in router choice.two isp(s) att UVERSE 20x4 mbits/sec , CABLE. 50x10 mbits/sec one office lan, individual physical desktops, and individual virtual machines as...
View ArticleER-X Confirming no input voltage sensor?
I've seen this asked before, but not for a while - and not regarding the ER-X. Based on the MIBS I see supported and the lack of an input voltage value in the UI - I think that the ER-X does not have...
View ArticleHelp needed with shaper policy
Hi All, I think I am getting myself all about face with this one and could use some help. I am trying to set up a traffic shaper policy for the following setup. LAN (10.20.0.5/24) --> VPN <-- LAN...
View ArticleDelete vtun0 interface.
I was following this guide trying to set up a vpn: https://help.ubnt.com/hc/en-us/articles/204949694-EdgeMAX-OpenVPN-Site-to-Site . Unfortunelty this failed. How can i delete the vtun0 interface?...
View ArticleIs it possibile to specify the "Host-Uniq" tag in PPPoE connection ?
Hello, new user here. I have a new fiber connection where the provider makes you use their router. I have put an Edgerouter-X behind the proprietary router and everything works, but I'd like to...
View ArticleTraffic Analysis loosing statistics
Does the Traffic Analysis tab only collect data for a certian period of time before clearing the statistics? Is there a way to increase the time period if it does? Currently running EdgeOSv1.8.0...
View ArticleEdgerouter X-SFP not providing POE
Good morning. I have been using my AP-AC-LR for about 4 months now using the POE injector along with an ASUS router with no issues. I replaced that router today with the Edgerouter X-SFP so that i...
View ArticleErLite 1.8.0 Read-only File system
Brand new ER-Lite device installed today.. Upgraded to firmware 1.8.0 just fine. Did some configuration in the GUI and at some point noticed errors. On the CLI I get:grknight@ubnt:~$ configure [edit]...
View ArticleCan't open SSH to WAN
I'm trying to setup remote SSH into the router. Not port forwarding to another server, but directly to the router itself. (I know it isn't best practice, but I don't have another option right now.)...
View ArticleVLAN throughput issue
I'm having an issue where traffic that is VLAN tagged to anything but ID 1 struggles to pass more than 20mbps but only in one direction.The setup is bridged throughout as follows:MIkrotik Core...
View ArticleUpgrade question on Edgerouter - from 1.7 to 1.8 without loosing customizations
hello, Pardon me if this has been discussed already somewhere in the forum. I am considering an upgrade on EdgeRouter from 1.7 to 1.8. Last time when I upgraded, I lost my freeradius install and it...
View ArticleERLite firmware upgrade over WAN
Hi Everyone, I currently have an EdgeRouter Lite in a remote location where I don't have physical access. It is running Firmware 1.5.0. I would like to upgrade to the latest version (1.8.0). I have...
View ArticleHelp with creating vlan or setting QOS for voip customer
I have a customer who has a public ip assigned to his router from us that is connected 4 hops away on a all bridge network design. When the issue occurs, which could be at any time they see their pings...
View Article