can't WAN on eth7
Just received ERPro-8. I used wizard WAN+2LAN2 and elaborated from the GUI to WAN on eth0, individual LANs on eth 1 thru eth4. I added firewall rules to WAN_IN, WAN_LOCAL & WAN_OUT (to block MS...
View ArticleMETA - Product Road-map Transparency
Given that there is reocurrent speculation about the intent with the EdgeMAX line (e.g. here), would it be possible to appoint someone like to start doing a blog series, or something, that would...
View ArticleCan't reach VLAN from LAN or viceversa
I'm fairly new to UBNT hardware, but I've managed to setup my basic network with only a couple of problems. I fixed everything but one issue, and I couldn't find anything that worked for me on the...
View ArticleUntagged Port on Router
https://help.ubnt.com/hc/en-us/articles/204959444-EdgeMAX-InterVLAN-Walkthrough-with-ERLite-3-using-Sample-Enterprise-Topology How would one set eth2 on the ERL to be untagged VLAN5 in this scenario,...
View ArticleSource address interface routing
Quesiton - I have a dual WAN setup and would like to route specific source address to one interface and not load balance those addresses. Tried searching for something similar on the forums but lost...
View ArticleClik here to view.
EdgeRouterX-SFP single mode sc modul
Hello guys,I bought this new router because I would like to have only one device for which ones i have two now. And i have problem with find which SFP modul should I used. I have single mode optic with...
View ArticlePACE 5268AC DMZ+ default IP address
Hope I am posting the question correctly or can be understood. I recently got the Edgerouter Lite. I have notice no matter which router you put behind the PACE 5268AC DMZ+, it will always give you the...
View Article[Support] EdgeRouter Lite, Unreliable Reboots / Failure
Hi everyone, I'm not entirely sure where to turn at this point. Here's my story; I bought an EdgeRouter Lite September '16. Set it up, and it has been running great for two months. After two months, I...
View ArticleWhere to create firewall rules? (web UI)
If I want to block access from the internal network to a web site on a specific IP address, how/where would I create a firewall rule to do it? I have an ERLite-3 and a very simple configuration with...
View ArticleIsolating Dynamic IPv6 on Guest VLAN
So I have native IPv6 from my cable provider, and as most people know it's not a static IP. I can get a /56, however. So I've set it up so my normal LAN gets one /64 and the Guest VLAN gets another...
View Articlelimiting traffic from a server on the LAN to the WAN
Hi, what would be the best way to limit traffic from a server (like a web server) that goes out to the internet? The purpose would be to make sure that such traffic doesn't occupy all the available...
View Articleedgemax edgerouter POE eth1 MIA
Hi. I have an issue in the web UI that my eth1 port is missing. The picture at the top shows the port as black and it's missing from the list of ports. I've attached a screenshot. The router seems...
View ArticleER-L PPPoE connection problem
Hello. I need some help with my ER-L!I'm currently using ER-L as a PPPoE dialer, which hooked up on a ISP-provided ONT in bridge mode. It is running as vanilla as it could: using wizard to set up PPPoE...
View ArticleClik here to view.
2 wan 5 LAN. 5 ip external adresses 1 of each lan
Hellow all, Someone askt me to make them a fail over network for a bunch of offices in 1 building.but i wonder if the edgemax ER8 Pro can do this. topology below The config needs to be on Wan 1 will...
View ArticlePPTP client not working when router is connected directly to ISP, but when...
Hello ladies and gentlemen,I have a problem that really confuses me and despite lots of reading, researching and some trial and error, I haven't found any solution. My router is EdgeRouter X with...
View ArticleFirewall question with bridged ethernet ports
Hello. I might already know the answer to this question, but wanted to verify as I have no way of testing it yet, and are on a very tight timeline when I can get to config it. I am changing an...
View ArticleCreate a Firewall Rule using Deep Packet Inspection (DPI)
Hi, I have an Egedrouter lite. I have created a firewall to block all the P2P application using DPI. When testing with bittorent, for 10 minutes of download is working fine. It’s blocking the P2P, but...
View ArticleL2TP server and OpenVPN client on the same router?
Hello, I have a L2TP server setup for remote access on my X router. Now I am looking for a SSL vpn service provider for internet access over VPN. I guess my question is, can both of those run at the...
View ArticleWAN on VLAN on ER-X switch, no internet on LAN
I tried replacing the supplied router from Dutch internet provider Telfort with a Edgerouter-X. They use tagged VLAN 4 for IPTV and VLAN34 for internet. I had already seen configurations on the...
View ArticleDestination NAT help for https
I have an Edgerouter Lite that is hosting a site with an Exchange Server running OWA on port 443. Currently the Source NAT is masquerading all traffic from BR0 out interface ETH2. The Exchange server...
View Article