Clik here to view.
Edgerouter lite 3+port forwarding: HELP!
Hello, I would like to open port 554 for this ip address:192.168.1.12 Eth2: Wan with DHCPEth0: Configures a 192.168.1.0 subnet with DHCP LAN server, serving addresses from 192.168.1.100 to...
View ArticleDNS Server doesn't work after upgrade to 1.9.1
After the upgrade to 1.9.1 on my Edgerouter Lite the DNS servers stopped working. I had to manually disable and enable the servers in the GUI and then they start giving out ip addresses again.
View ArticleClik here to view.
Issue or bug v1.9.1
Hi all,Just information, I'm run ERPOE 5 v1.9.1 configure failover and running well so far.but I noticed a few readings that may not fit on bar GUI routes the top left corner.Like example this pic:GUI...
View ArticleHairpin NAT doesn't seem to work
I have an EdgeRouter Lite running V1.91 . Trying to connect my SONOS music system to a PLEX server that are both on the same network (I'm running WAN on ETH1 and LAN on ETH2). SONOS sees plex so it...
View ArticleBasic EdgeRouter ERLITE3 subnet setup help
I'm setting up a small office network. I've only setup simple home networks before where all the ethernet ports on the back are like a single interface. My goal is to create 3 subnets (192.168.1, .5,...
View ArticleVPN on the same IP range
Hello. Fairly new to this level of networking detail. I have been able to set up a L2TP VPN successfully to do what I need. I am using MacOS and iOS as clients. Everything works fine with the VPN (when...
View ArticleEdgeRouter X - Managed switch0
I'm trying to use the internal switch0 as a managed switch with VLAN tagging and I'm running into something very weird. This following article shows how to configure access and trunk...
View ArticleClik here to view.
Router disconnects from everything then reconnects
I have a new installation. It is WAN (cable modem) on eth0, and four independent subnets, one on each of eth1-eth4:10.0.1.0/2410.0.2.0/2410.0.3.0/2410.0.4.0/24 Each subnet has a separate DHCP server....
View ArticleAT&T Fiber service blocks NTP 123/udp outbound. Anyway around this?
I first started noticing this when my Cisco phones stopped displaying the time. After banging my head around trying to get my ERL to sync its clock via NTPd for my clients, I discovered AT&T is...
View Articleaccess vpn from inside the lan
I was wondering what config change I may have to make to get VPN access to work from inside the LAN. setup: ERPro-8 running v1.9.01-1NAT -- source and destination NAT for public to LAN ip for VPN...
View ArticlePass-Through L2TP/IPSEC to Lan VPN Server
Hey folks, I'm looking to allow incoming L2TP/IPSEC connections to pass-through my EdgeMax Pro-8 to my internal Windows Server 2012 R2 running a VPN service role. I've read a few howto's and tried a...
View ArticleEdgeRouter IP not showing on Eth0
I need some help on my EdgeRouter. I used the WAN + 2LAN2 Wizard and stayed with the default options. I have a good Internet connection that I can connect to a laptop and verify. I take the working...
View ArticleWhat would you say are the most common EdgeMAX support issues?
We're aiming to identify the top support-related issues that are encountered on EdgeRouter and EdgeSwitch, both here and via support tickets, to identify what we can do to help reduce incidence of...
View ArticleL2TP VPN Constantly Disconnecting
Hello -- I was able to find a ton of different tutorials on how to set up a VPN, and they worked great and I was able to connect immediately. However, after a couple minutes the connection almost...
View ArticleForward an IP address to a different IP address
I want all outgoing traffic going to a specific IP address to actually go to a different IP address, BUT only for a certain network group. I have servers in a network group, and if they attempt to...
View ArticlePPTP and HTTPS issues
Hello, I'v recently had problems with my ERLite-3 not letting me access certain HTTPS based websites, such as https://github.com/ while connected to my VPN using PPTP on the ERLite-3.When trying to...
View ArticleDNSMASQ address= settings
I have an Apple TV 3 running Plex Connect (running on a QNAP NAS). I had the following lines in my old Tomato router: address=/trailers.apple.com/192.168.73.4address=/atv.plexconnect/192.168.73.4 in...
View ArticleBlock WEB Gui outside the network?
Hi, I have a EdgeMax X SPF Router and have a question how do I close the external connection to the web gui EdgeOS from outside. Now I can enter the external IP-address and login to the system. And...
View ArticleWhere to find firewall rule stats from terminal
Hi All I have an EdgeRouter Lite-3 which I've setup with a zone based firewall, a couple of VLAN's and an inbound and outbound VPN. This means that I have quite a few firewall rules. I'd like to...
View ArticleFirmware 1.9.1 on R6 broke fiber port
Hi, Yesterday we updated EdgePoint R6 to 1.9.1 and lost connection to EdgeSwitch S16 at v 1.7.0. Downgrade to 1.9.0 solved the issue.SFP modules are from Mikrotik, detected as Model S-85DLC05D...
View Article