Newbie question - To VLAN or not on the Guest network.
Another newbie here from an Asus router switching to the edgemax. I used 2lan+wan wizard. eth0 - WANeth1 - 192.168.1.1/24 (guest network)switch0 - eth2 - eth4 (internal network) eth1 will connect to my...
View ArticleBlock HTTPS site
Is there any way at all to block HTTPS sites without using a non - transparent proxy? I have one site in particular that I need to block but nothing that I've tried so far works.
View ArticleNeed help routing between 2 networks
Hi. I have an EdgeMax PoE (fw v1.9.1) and would like to use it to connect 2 networks for the purpose of allowing open traffic and discovery between the 2 subnets. It is for a home network so no...
View ArticleWhat are people's thoughts on edgeRouter with Verizon modem (internet only)
Hello all, I'm just curious seeing that I selected verizon service for my new place. I'm suspecting that the ONT will use Coax, considering that's what's configured on the floors above. I'm wondering...
View ArticleClik here to view.
Network layout help needed. VLANS?
Not sure if this is the most appropriate place for this, but I use a few different Ubiquiti products to make it all work. Currently I have 2 farm sites with internet at the house and computer in the...
View ArticleSpecific Domain Access Restrictions
I am using edgerouter POE (EdgeRouter PoE v1.9.1alpha2)There are multiple domains connected to a single public IPFor example, to connect to a server using ssh or RDP, you can use aaa.com as a specific...
View ArticleEdgerouter POE slow wired connection
I have 1.9.1 installed with a WAN+2LAN2 setup My internet is on eth0My PC is on eth3My Unifi AP-AC-Lite is on eth4 I get 120Mbps down on the wifi, but I get half that on the wired connection. I got...
View ArticleClik here to view.
dealing with ridiculously low bandwidth and VOIP
Hi, I've been trying to figure out the best way to deal with having a ridiculously low bandwidth and wanting to make phone calls. The advice I could find in the knowledge base suggest using traffic...
View Articleupgrade without redo?
Hi, is there a way to upgrade the firmware without having to do the configuration all over again?
View ArticlePort forwarding problem multiple interfaces
I don't get why Ubiquiti has to make port forwarding associated to LAN/WAN. How to do a port forwarding and ensure return path is properly translated? It is not obvious how to configure port forwarding...
View ArticleStatic IP on EdgeRouter POE
I am having a lot of trouble configuring my EdgeRouter POE as a home router with a static WAN IP address. Never had this problem before with any router.My WAN is on Eth 1. When I put this interface in...
View ArticleClik here to view.
Network setup - help needed
Hello guys, I think I have over estimated my knowledge in network setup and I need you help. The problem is how to setup Edge Router Lite + EdgeSwitch 8 + Unifi AC-PRO behind ISP router? So, I have ISP...
View Articleunable to execute /sbin/reboot: Input/output erro
Hi, Another bug ? reboot Proceed with reboot? [confirm][y] sudo: unable to execute /sbin/reboot: Input/output error
View ArticleDNS resolution of shortnames (mostly) broken after I upgraded my EdgeRouter...
I think this set of nslookup and ping commands I issued will help explain:C:\>nslookup apc Server: ubnt-home.lab.local Address: 10.10.1.1 Name: apc Address: 10.10.1.3 C:\>nslookup apc.lab.local...
View ArticleDual WAN with Dual Routers
Can anyone provide an example of using two routers, two ISPs and VRRP on the LAN side in order to obtain reduncancy within the network? I'm looking for a setup very similar to the diagram below....
View Articleopposite of "set system ipv6 disable"
I was debugging some network issues and I wanted to temporarily disable ipv6 on my ER-X, so I did a:set system ipv6 disable set system ipv6 disable-forwarding commitHow do I "undo" this? Everything...
View ArticleMore simpleton shaping questions
If I create a shaping policy called "office" and I apply that policy to an interface such as a vti tunnel coming from one site. Can I apply that same policy to another vti leading to another site?...
View ArticleEdge Router Home Use
Setup Edge Router ERPOE-5 with 2 AP-Lites and one UAP-AC-Pro in my home, simple configuration under WAN +2LAN2 with bridged ports. All seems well with the exception of logging into a specific bank...
View ArticleVoIP - ingress cuts off
I setup my first EdgeRouter X and updated to firmware v1.9.1. It is setup as a basic router using the wizard with a Comcast static IP on the eth0 and eth1 is connected to the LAN. I have noticed since...
View ArticleEdgeRouter local user password visibility
We have an EdgeRouter upgraded to 1.9.0. The unit is setup for L2TP remote access with local-user authentication. The issue is when you log into the GUI of the edgerouter and go into the config tree...
View Article