Accessing servers on a different subnet
I'm unable to access some servers on a different subnet. Here's an overview of my setup:The edge router is my gateway. I'm running a EdgeRouter PoEv1.9.0 (5 port). The servers that I want to access...
View ArticleName resolution across OpenVPN
Hello... Some context: My ER-X router is "managing" my home lan: the dnsmasq inside er-x manages the "phi8.home" domain: any clients in my home network can for example do "ping thewall.phi8.home" and...
View ArticleGame QoS Performance Impact with Edge Router PoE?
I'm looking for a router solution to run in a gaming environment with QoS priority queues and am curious what to expect with the Edge Router PoE.Right now we have a consumer grade TP-Link router which...
View ArticleER-X-SFP configured as switch-how put default gateway
You can configure default gateway on ER-X-Sfp? I found no option for the default gateway and no access from another network segment.ubnt@SwOtelecMain# show interfaces switch switch0...
View ArticleHow to route all traffic to external ip over specific interface/gateway
Hello! I need to route all trafic from my PBX to SIP provider over one specific WAN interface. I tried to make static route but still traffic goes through any WAN. Help please!
View ArticleDual WAN Load Balance
I used the Load Balance wizard to setup my 2 WAN / 1 WAN network. Download speed for the WAN's is about even, while the upload speed is 1X and 5X. What is the best way to make sure that when using FTP,...
View ArticleSourced Based Routing Still broken ERX V1.9.1Beta1
As mentioned in this thread:https://community.ubnt.com/t5/EdgeMAX/Policy-based-routing-source-address-based-not-working-in-EdgeMAX/td-p/1648890 firewall { all-ping enable broadcast-ping disable...
View ArticleHow can I manually block dns hosts for LAN on EdgeRouter X without complex...
I'm looking for easy solution of blocking dns hosts for LAN on ER-X. I'd prefer to make changes manually and FTP the updated file. Something like...
View ArticleFirewall default action and Wan failover
Hi All Normaly I work on Cisco and Juniper so i'm quite new to this. I have 2 questions I cannot seem to find a answer to: I have made a set of firewall rules for all my vlans, but when default action...
View ArticleVLAN over tunnel between Mikrotik and ER-X? Is it possible?
Hello All, I need to connect 2 locations via IPSEC tunnel. Home location will be managed by ER-X and the remote location by Mikrotik. The intention is to carry an untouched VLAN over the tunnel. I was...
View ArticleClik here to view.
Basic Queues - what am I doing wrong?
I'm trying to set per client bandwidth limits (for two different VLANs/subnets) using HFQ in Basic Queues, but I keep getting "Failed to apply the configuration". How am I messing this up?
View ArticleCannot assign guest SSID to VLAN
I have an access point running dd-wrt and I set it up to tag one of the SSIDs with a VLAN tag (101). I also set up my UER to have a VLAN on switch0 with the same tag. The problem is the SSID is not...
View ArticleER-X suitable for my weird set-up? Isolate IOT devices
Is it possible to configure the ER-X to allow devices on one VLAN to access devices on another but not the other way around? I'm trying to set up my network so my various IoT / smart devices are as...
View ArticleClik here to view.
VPN - Site To Site - General Info needed
Hi TeamI need to configure a Site to site VPN and insert the ISAKMP and IPSEC settings. I believe I can do this in the config tree (I want to use the GUI ideally as i dont know CLI yet). These are the...
View ArticleEdgerouter R6 issue
I had an edgerouter that stopped passing traffic the other day. All radios connected to it were still powered on and were connected.The edgerouter is acting as a simple switch.We power cycled the...
View ArticleDual WAN, destination NAT, no failover, no load-balancing - How should I do...
I'm configuring an EdgeRouter Lite with firmware v1.9.0. eth0 is connected to ISP 1 which will be the ISP used for internet traffic.eth1 is connected to ISP 2 which will be used for specific network...
View ArticleEdgerouter lite ipsec site to site vpn
Hello, I'm new to Ubiquiti products however I do have some expereince configuring Cisco equipment. I'm trying to set up a IPSec site-to-site VPN between two EdgeRouter Lites running firmware 1.9.0...
View ArticlePolicy route openvpn traffic
Looking to see if someone can look at my config and help me understand why my policy route is not working.firewall { all-ping enable broadcast-ping disable ipv6-receive-redirects disable ipv6-src-route...
View ArticleVLAN Routing Help
Hello, Hoping someone will give me a hand with this. Eth0-DHCP from ISP Eth1- Trunk to HP1910VLAN 20 Biz 10.10.20.1 (DHCP 10.10.20.10-254)VLAN 30 Pub 10.10.30.1 (DHCP 10.10.30.10-254)No routing...
View Article