EdgeMax CLI vlan
I have a EdgeMax Switch POE-5 running v1.9.0 I am trying to setup some of my interfaces on different vlan and assign ip helper on it. Seems like the EdgeSwitch CLI commands documentation is not valid...
View ArticleERL Lite 3 Question
Hello, I am brand new to VLans, and I have been reading a bunch over the past few weeks.I purchased a ERL-3 and 2 ES-8 switches. I owed already a cisco sg200.So starting from scratch, My router (ERL-3)...
View ArticleSNMP Trap on VPN up/down
I was able to configureSNMP v3 auth and trap target. But can not find any example how to configure snmp trap. In particular I am looking for information on how to configure traps on S2S VPN up/down....
View ArticleEdgeRouter Lite Refuse packets
Hi, I'm trying to configure my network with some VLAN's. For that I'm using an Edge Router Lite and an EdgeSwitch 24-Port 250W. Before I started with the configuration I read this article:...
View ArticleDual WAN routing problem
I have run into an issue that I can't figure out. We have 2 WAN links, one is static (eth0) and the other DHCP (eth1). We want to use eth0 for all traffic and then route specific traffic out eth1. How...
View ArticleIsolate subnets from accessing each other?
Say I have up and running 3 DHCP servers on EdgeRouter X:192.168.1.0/24 - assigned to a switch interface (switch0);172.16.1.0/24 - assigned to VLAN1;172.16.2.0/24 - assigned to VLAN2.Each one of them...
View ArticleWAN failover review and log question
Hi folks, We had an outage today on our primary link and failover didn't work as expected. The load-balance watchdog shows: Group WAN_FAILOVER eth0.10 status: Running pings: 6276 fails: 7 run fails:...
View ArticleBasic EdgeRouter POE + UniFi Switch 8 POE + UniFi AP AC Pro configuration...
Hi everyone, I have been using my EdgeRouter POE for over a year now as the primary router/firewall for my home. It is connected to my ISP-provided gateway, in bridge mode. Recently, I also purchased a...
View Article1:1 Nat for CPEs
I am new to EdgeRouters, so my apologies up front. Now for the question... etho is my interneteth1 is laneth1.101 is my broadband /24 block 123.123.123.1/24 (public) and 192.168.0.1/24 (Private for...
View ArticleClik here to view.
Fix Smart Queue label error
In the Smart Queue there is a error of the labels as I show in the picture where it say Upload is actualy the Download speed and viceversa.
View ArticleClik here to view.
ERPOE5 cannot reach eth0 subnet from switch0 subnet
Appreaciate advise. I have 1WAN+2LAN on erpoe5 all standard, but cannot access switch0 (192.168.2.x) devices from LAN eth0 (192.168.1.x) my my understanding it should be routed between these two...
View ArticleHelp with Zone based firewall - advice wanted
Hi! I want to ask for some guidiance and help setting up my network. I am new to this but have learned a lot from these forums! Without any previos knowledge of firewalls, I felt that Zone Based...
View ArticleHow to configure EdgeMax POE 5 port router
I have the EdgeMax 5POE 5 port router that I would like to setup as a network. I have PC, two Raspberry Pi devices, an audio mixer and the last port, I wish to connect a Netgear 8 port switch for...
View ArticleThird WAN Automatic3G/4G mobile broadband failover
Hi everyone, Could somebody possibly help? My small business client are looking to upgrade their existing router: Netgear ProSafe FVS336G. This router currently has 2 x fibre, load balanced WAN PPoE...
View ArticleHelp understanding logging
I'm trying to understand what this is in my log as it happens once every one to two minutes and filling up the log: kernel: IPv4: host 192.168.1.70/if2 ignores redirects for 192.168.1.62 to...
View ArticleLooking to replace my PFsense box... which edgerouter?
I have been looking to replace my pfsense box, as I want to power down that computer. I have 1GB fibre (symetrical) at home, that I connect via PPPoE, so there is that. In the PFSENSE box, I have set...
View ArticlePort Forwarding, Open Ports, SIP ALG & QOS
Hi Team Wonder if you can help. I am VERY new to using these Edgemax Pro routers and I have a EdgePro 8 which so far I love and hope to master in full. I use the GUI to set things up as coding is a bit...
View ArticleFirewall for several vlans
Hi guys!! In a scenario with ERPoe-5 where several vlans for each traffic type. For example:- vlan10: virutalization server- vlan20: virtuals servers- vlan30: lan clients A- vlan40: lan clients B-...
View ArticleNeed another pair of eyes for zone-policy problem
I have a script that generates my firewall rules, which I then cut-and-paste into the CLI. I'd doing SOMEthing stupid here but I've been banging my head against it all day with no luck. Normally, when...
View Article