L2TP Server Connected with No Network Access
Hi, I followed this guide: https://help.ubnt.com/hc/en-us/articles/204959404-EdgeMAX-Set-up-L2TP-over-IPsec-VPN-server To create L2TP Server on EdgeOS 1.9 over Dynamic IP PPPoE. I sucessful connect the...
View ArticleNext-Hop Verification on Static Routes?
I am looking for a method for defined routes to be either marked active or inactive based on next-hop verification. Many of the devices (such as air-max radios) do not support routing protocols so I...
View ArticleNew ERX user - looking for advice / help forward planning network
Hi, hoping I can get a steer / sense check from those with more knowledge / experience. I'm pretty comfortable with a bit of *nix CLI work as a freelance web dev, but my knowledge of networking is...
View Articleremote access
Would like to open remote access to the router but need some way of setting that three bad passwords closes access for half hour or something like that
View Articleedge router pro 8 email traffic
Hi Anyone put me in the right direction to send all email traffic from 1 vlan to one of the 2 wan connections.need to isolate issues with not all emails being sent and received.Thanks
View ArticleL2TP VPN works fine via Windows 10 but will not work from iPhone or iPad...
Hey everyone, I've been trying to figure out why my VPN is working fine on my desktop pc but not on my iphone or ipad. I'd appreciate any help. (Config file attached) Here's my current VPN config:...
View Articleconnecting to WAN causes disconnect
I have a ERPoE5. I used the wizard to set up WAN+2LAN2. I can connect locally via eth2-4 ports to the ER. But when I connect the ER to my cablemodem, I lose connection to the ER. I have no WAN...
View ArticleCopy config via console port
I am connected to EdgeRouter Lite via the console port and a FTDI usb serial cable. I am using Putty and am successful logging into the router and use CLI. I want to copy the config file to my...
View ArticleTwo ERPOE-5s: one creates a PPTP interface, the other doesn't.
I have two ERPOE-5s sitting on my desk right now that I'm trying to set up for PPTP VPN access, and there's some odd behaviour on one that isn't happening on the other. Both are running firmware...
View Article1 ISP, 2 DHCP IP's on different subnets
My ISP provides 2 DHCP IP's on different subnets. I use 2 consumer routers to connect to a mini switch that in turn connects to cable modem. One router serves home devices...
View Articlecellphone cannot reach or pickup my file server
My Network Setup: ERlite-3 and unifi APMy router is setup wlan+2lan2(eth1-10.0.1.0/24, eth2-10.0.2.0/24) my AP is directly connected to eth1(1.0) and a netgear swith on eth2(2.0) my file server and...
View ArticleER-L static route not followed
Hi folks - I am new to the ER and haven't got my head around CLI yet, so be patient! I have two routers in use, the new ER-L (A) (replacing an old box) and one with a legacy VPN in place (B). When a...
View ArticleIPSec VPN Problem
I have a simple IPSec VPN setup between a remote site using an ER-X and an old Cisco router (soon to be replaced so I can use OpenVPN instead). I have used the GUI to set up the VPN. I could get the...
View ArticleClik here to view.
Edge Max config - 4 WANs to 3 VLANs
Hello, can you please navigate me what procedure should I use to have this setup. I have 4 different internet providers which are connected to Egde Max router ports ETH0, ETH1, ETH2 and ETH3. Port ETH7...
View ArticleER‑X‑SFP + UAP‑AC‑LR Newbie Setup
Sorry to post such a basic request for all you network wizards. This is my first UBNT setup. Goal: To connect 1 local hardwire PC and 1 AP-AC-LR to the router and that both the local PC and those...
View ArticleIPTV ERX
If anyone can help, ive read up on igmp and tried the configs in this forum, i have my Huawei ONt connected to the ERX and im trying to route both Internet and iptv thru switch0 im attaching the info...
View ArticleUnable to re-enable ports on ER-Pro8
Hello All! I've got EdgeRouter Pro-8s deployed at 6 locations. All are running 1.9.0 software and are working great. One of them has a problem that I'm not sure where to start on. Being that these...
View ArticlePhysical port isolation in EdgeRouter Lite
I am trying to basically isolate the two physical ethernet ports eth1 (192.168.1.24) and eth 2 (192.168.2.0/24) in EdgeRouter Lite. I have created two firewall rulesets one for each as mentioned in...
View ArticleConnecting to Edgerouter x after initial setup
Using the setup wizard on the Edgerouter X I applied my changes so it was setup as a single LAN. I now have a cable coming from my wireless router to the eth0 port and cable from eth1 to my laptop (I...
View ArticleMultiple failover
Can ubnt handle this kind of setup? eth0 = managementport [192.168.1.1]eth1 = ISP1eth2 = ISP2eth3 = ISP3eth4 = using a private ip [ex 192.168.2.1/24], primary internet eth1, failoveronly to eth2eth5 =...
View Article