EdgePoint EP-R6 Untagged VLAN
Hello! We use EdgePoint EP-R6 all ethernet port in switch mode.We want to only one Untagged VLAN (Port PVID) to eth0. How can we do this in the simplest way? Thanks in advance. Attila
View ArticleConnections dropping with Multi-WAN set-up
Hi All, I've configured a multi-wan setup using the below guide:https://help.ubnt.com/hc/en-us/articles/205145990-EdgeMAX-Dual-WAN-Load-Balance-Feature I've put sticky on both destination and source...
View ArticleBeta release v1.8.5beta2 changes with IPsec Site to Site
Is there any new config information on IPsec Site to Site with software version 1.8.5beta2? My 2 questions are. 1. Currently my tunnels are handled by AT&T, the tunnel devices are IPsec Site to...
View ArticleBGP - Need help with routes
I guess I should start a new post about this. Just got a BGP VPN setup with AWS. Both tunnels are up, AWS looks good, except it says:VPN Tunnel | IP Address | Status | Status Last Changed |...
View ArticleWAN connection - modem hangup frequently
I'm having an issue with regular frequent loss of WAN connectivity on my ERLite-3. The outages are always the same duration and the timing is of two frequencies. My config is: Zyxel VDSL in full bridge...
View ArticleBUG: dhcpd: uid lease xxx.xxx.x.x for client xx:xx:xx:xx:xx:xx is duplicate
- ERPOE ver 1.8.0- We get these in the message file- Happens EVERY 12 hours- ALL are from Ubiquiti devices- ALL devices have STATIC IP- ALL LANS are set: Authoritive enable- ALL below devices on same...
View ArticleDPI - Streaming Media
On the EdgeRouter Lite3 and the 5 models when I have been playing with DPI it does classify YouTube as Streaming-Media. I have created a rule based on the example here:...
View ArticleExclude IP address from load balancing
Hey guysI have setup the Edge Router lite with 2 WAN connections on eth0 and eth1 i am using load balancing i have a DHCP for my network on eth2 and a Vlan on eth2.50 I have a server setup on eth2 with...
View Articleclear load-balance counters
Does anybody know how to clear the load-balance counters so when I do show load-balance status it starts back at zero? Cheers
View ArticleSNMP Settings Lost By Reboot
Hi, Just wanted to report that on my ER-X-SFP I lose all SNMP settings when rebooting the box. This happened on the 1.8.5alpha and happened again when rebooting to upgrade to 1.8.5beta2. I am not sure...
View ArticleHelp with PBR
Hi all, I am having difficulties with getting the PBR working...Basically I have 2 routing tables, and a modify rule on IN f the switch0 to modify the routing based on the ip address of the client.The...
View ArticleERP 8 Port - Switch Ports
Hey guys, Need to test a simple setup and have never used the EdgeOS before but I'm familiar with Juniper. I have my base setup done with WAN on eth0 and LAN on eth1 with internal address and NAT...
View ArticlePCP: External IP in request didn't match interface IP
I'm seeing the following message frequently in my logs, "PCP: External IP in request didn't match interface IP". I'm also seeing Back to My Mac fail to create any mappings. This seems to match an issue...
View ArticleNewbie question: can I limit traffic this way?
I'd like for certain devices to have certain traffic limited during certain time slots. E.g. I'd like iPads that are used for school work (and do not need youtube access for that) not to be able to...
View ArticleCan I reset traffic analysis stats?
Traffic analysis is a great feature, but a couple of devices on my network use a lot of bandwidth and then drown out the ones I might be interested in. Currently, when I'm interested in the less heavy...
View ArticleEdgerouter Lite issues
Hello all,I'm just learning how to use this router. I was out of town and coma back to find my network unresponsive. My edgerouter Lite was unreachable. I restarted it and in the CLI it hangs at boot...
View ArticleClik here to view.
Edge Router X Multi VLAN Configuration / Trunking Issues
Hello Everyone, I hope I am posting in the most appropriate thread. I've done quite a bit of reading, and a lot of banging my head up against a wall for the last week and a half. I am probably...
View ArticleOSPFv3 and Palo-Alto - Neighbor won't come up
I've got a few PA 3000 series firewalls that talk OSPFv3 to Cisco gear and that works great. The OSPFv3 config on the PA side is dead simple, basically area 0.0.0.0, router ID set and a small set of...
View ArticleEdgeMAX + UniFi and layer 3 roaming? Possible to transfer roam stateful...
I have a couple small networks I'm builing (my home + friends). They all will consist of one EdgeRouter PoE and two UAP-AC-LITEs. I initially was planning on not bridging the two ports that the APs...
View Articledhcpv6-pd client questions
TWC, dhcpv6-pd configured for vlan interfaces on local network. wan ineterface has a separate /64. 1) What does the log mean? Everything seems to be working as intended$ show dhcpv6-pd logMay/21/2016...
View Article