Force Static IP
How can I force a static IP to a particular mac address on subnet other than the one running DHCP? My network is currently running on 192.168.1.0/24. I am slowly making a transition to 10.0.0.0/21....
View ArticleClik here to view.
web GUI/edgeOS no live data (solved)
Loged into my edgerouter x 5 port today and it will not show any live data such as the tx and rx graphs, witch rj45 ports are active, cpu and ram usage, loged on users. basicly the gui loads but it is...
View ArticleBest 12v UPS for Ubiquiti gear
I'm exploring alternatives to wall warts as my entire network (minus the server) runs on 12v. Between my ERL, hard drives, and Netgear switch, everything is rated at 12v 1-3A. Is there a UPS that has...
View Articleupnp and qnap
what configuration i can use in edgerouter?for use use qnap function upnp!! only enable upnp or upnp? i have wan on eth0 and LAN switch 0 <---eth1,2,3,4 i have QNAP on eth3 upnp configured arent...
View ArticleEdgeRouter Pro DHCP for 2 interface
I recently bought an edgerouter pro and a UniFi AP AC LR and is trying to set it up.On the router I have eth0 and eth1 connected to WAN. eth1 (ip: 192.168.0.1/22) connected to switch with DHCP enabled...
View ArticleERPro + VLAN + UAP-PRO-CA + CISCO/UNIFI Switches
Not sure where to post this, but since the ERPro is handing out DHCP for the VLAN.... When I try to get DHCP with my guest ap, I get this: Sometimes it connects right away. Then others I see...
View ArticleRunning OpenVPN on an ER8: 1.9.0 Issues.
Hi All... Up until v1.9.0 the OpenVPN server on my ER8 worked perfectly. I could log in and access all internal systems and even surf the Internet. I must also say, I run a Load Balance configuration....
View ArticleEdgeMax Router + AirFiber + Cisco Switch
I hope someone can help me. I'm fairly new to Ubiquiti and somehow confused. We have 3 Airfiber connected with each other. Airfiber 1 (SITE A) - is trunk to the Cisco Switch and Juniper in which the...
View ArticleDoes EdgeRouter Lite support PPPoE with CHAP as client?
I'm planning to upgrade my home router. My provider's docs say that they use PPPoE with CHAP. Is EdgeRouter Lite up to the task? Also, does it have a GUI for this? (Provider's older lines used PPPoE...
View ArticleDisable ICMP Redirects
I have a problem that I'm trying to resolve and I need to disable ICMP redirects. This router is used for routing through ospf with no firewall enabled. I found these two commands which i've commited:...
View ArticleRFC1918 leaks on WAN IF
I'm seeing some weird RFC1918 traffic on my WAN interface.So far i've only seen it from 2 clients. I can trigger it on one machine by shutting it down, whereafter it will send out RST,ACK packages. In...
View ArticleRouting Table Entry 0.0.0.0/24
I have an edgerouter set up for our company. I have added an openvpn server which is working well. I am seeing the following entry in the routing table:Selected Destination Interface Route Type...
View ArticleMulti-WAN VPN down again
I originally posted here and the issue appeared to be working (for several hours infact). But now the VPN is down again and I'm stuck. I've actually got this problem at 2 sites, both using ERL, both...
View ArticleInternet down when primary is down, but secondary is still up (on Multi-WAN)
I can unplug/disconnect my secondary WAN and everything continues to work like normal. However, when I disconnect the primary, the system (load-balance status) reports both connections as down, it...
View ArticleSome NAT retransmit problem happens in ERPOE-5 with firmware 1.9.0
I got my ERPOE-5 last week.When I use iperf3, I find the retransmit value is a little high. Although there are no problem in normal use.I test both default firmware (1.2.0) and the lastest firmware...
View ArticleNoob UPNP Question
I'm trying to enable upnp for the "back to my mac" function of my imac. I did some googling and I thought I had it figured out. I enabled the upnp2 service for the port connected to my switch but it...
View ArticleRADIUS Login MSCHAPV2
Hi, I was working on configuring my EdgeRouter and EdgeSwitch to authenticate against my RADIUS server for router and switch users, and I noticed it only works with PAP. Is there an option to have it...
View ArticleIPsec Configuration
Hi guys , im not the best in tworking and I need some help . I have a problem configuring IPsec with the edgerouter PoE. I enter all the information in the IPsec Gui with Automatically open firewall...
View ArticleSending firewall logs to remote syslog on non-standard port
I setup a Nagios Log server on my network and want to configure my edgemax router to send it's logs to said server. The issue is that the Nagios listens on port 5544 and not 514. Where on the edgemax...
View ArticleFirewall Openings for Phone
I am new to this and we are having an issue with our phone system. Our phone vendor told us to do the following:Please have your IT vendor make sure that the firewall at this location is allowing all...
View Article