ERL Failover with VLANs
So, I'm trying to setup an ERL with failover AND VLans. The failover I seem to have figured out... but when I add vlans into the mix stuff doesn't work. I used the loadbalancing wizard. eth0 is lan...
View ArticleEdgeMax L2TP VPN issues
vpn {ipsec {auto-firewall-nat-exclude disableipsec-interfaces {interface eth0}nat-networks {allowed-network 0.0.0.0/0 {}}nat-traversal enable}l2tp {remote-access {authentication {local-users {}mode...
View ArticleDNS Forwarding
Good Afternoon: ERLite running 1.9 here. Current configuration, DNS forwarding was working fine for atleast two week. This morning I wake up and find internet is down, still able to ping 8.8.8.8....
View ArticleClik here to view.
EdgeMax QoS disambiguation(FQ_CODEL, HFQ, SFQ, etc)
Hello, Can anyone shed some light on the correct way of configuration Basic and/or advanced QoS rules? For the basic, my primary needs are serviced based QoS for VoIP/Skpye/general RTP traffic. Via...
View ArticleBlock VLAN from internal IP address
I have a VALN just for my VPN traffic and I have a server on a seperate VLAN. Is it possible to block access from the VPN VLAN to that specific server so that when I am on the VPN, my client uses the...
View ArticleDNAT rule will not fire if inside/outside port numbers are different
Config attached. I have a need to open a single high port number and translate to 3389 on the inside for rdp. Problem is I can't get it to work in a traditional dnat. If I make the port numbers the...
View ArticleLooking for Matching and Deny Capability in for DHCP
I wanted to use the DHCP ability to match on hardware addresses to deny specific sets of machines from getting IP addresses. These ip addresses will provided via another DHCP server on the same network...
View ArticleClik here to view.
Cannot access Internet from VLAN
Hi, I have created a few VLANs according to this article . Problem is that I can't get internet access from VLAN when this rules are enabled. some additional screenshot of my configuration......
View Articleclamp-mss-to-pmtu
Hi,iptables has a nice feature to circumnvent broken Path MTU Discovery with TCP protocol: Maximum Segment Size clamping. I can manually set the MSS to a fixed valued via CLI/GUI, which is okay in...
View ArticleClik here to view.
Edgerouter Pro 8 rebooting itself
My Edgerouter started rebooting itself two days ago. It did it first around 2pm on Tuesday. Then almost exactly 24 hrs later it rebooted twice. It's rebooted once so far this morning (It's 9:30am...
View Articlesplit tunnel by VLAN
Hi, I am looking to upgrade my home setup, and interested in the edgemax (I currently use the ubnt wireless). I have an interesting setup. I have my home router with both my local VLAN and a guest...
View ArticleDPI for iMessage
Not super criticial but it seems that the DPI definition for iMessage is not up-to-date or is no longer working when I use it in a firewall rule for Apple iMessage both on the iphone and OSX. For...
View ArticleKudos to SquareTrade Extended Warranty
It’s not often I experience service from an extended warranty company that goes so far beyond the letter of its contract that I feel compelled to share it with owners of similar equipment. For about 22...
View ArticleER-X POE passthrough
I have an ER-X and an UAP-AC-LITE that came with a Power injector.Is this power injector enough to power both devices, the ER-X and the AP thru the POE passthrough? Thank you,
View ArticleIssue Bridging Multiple VLANS Over EPR8/EPR6
Hello all! I am experiencing an issue trying to bridge a couple of VLANS over multiple ETH interfaces on an EPR8. I have also tested this with an EPR6 and am still having issues pinging my gateway....
View ArticleSite-to-site options at UBNT?
Why am I not surprised that it looks like there are multiple products and options for doing a multi-site VPN... A small company has three offices and would like to connect them over the Internet with...
View ArticleSuggested EdgeRouterX Configuration
Hello, Let me preface: I am not even remotely an expert in computer networking or computer science. I am able to navigate CLI in Linux decently enough, but beyond this I have a very cursory knowledge...
View ArticleCan't get hairpin NAT to work despite extensive research...
I have research numerous websites and forums, yet I still can't get the hairpin NAT to work on my home network with the Edgerouter X. Please help!!WAN -> eth0server-> eth2 firewall { all-ping...
View ArticleEdgeRouter Pro v1.9 Site to Site Multi-WAN VPN, Load Balancing, Failover,...
I am trying to figure out where to start with my setup then actually get all of this dream into reality. Problem is there is ton's of information, limited GUI, and I don't even know what VPN option is...
View ArticleIPSec VPN WAN Failover - Possible?
assisted me earlier this week with a load balanced IPsec VPN issue, where I had to hardcode my WAN1 IP to get the tunnel to route traffic. I had a follow-up question, is it possible to make the IPsec...
View Article