Hardware accelerated qos
I've read many times about how turning on qos stops hardware acceleration working and therefore limiting throughput performance. Is this a hardware limitation of the cavium processor, or is it possible...
View Articlet-mobile cellspot
Anyone have a t-mobile cellspot at home working with ubiquiti. (https://support.t-mobile.com/community/coverage/personal-cellspot/4g-lte-cellspot) I've tried forwarding UDP 4500,500,123 yet it still...
View ArticleERL v1.9.0 - Flaky 'connection' - Packet loss mostly
I just upgraded my router a few days ago to v1.9.0 (from v1.8.5) and seem to randomly have some packet loss. Pinging a few domains (and using mtr) seem to all point at my ERL being the issue. I started...
View ArticleDynDns problems
I have DynDns set up on my ER-X and for some reason it does not update the ip address when it changes. Here are my dynamic dns settings: Interface: Eth0Web: DynDnsWeb-Skip: This box is blank Service:...
View ArticleL2TP over IPSEC
Is it possible to set up VPN with a dynamic IP and dynamic dns hostname instead of ip address in client settings?
View ArticleSystem log server
Does anyone have any recommendations on a System log server? And some pointers on how to set it up?
View ArticleClik here to view.
EdgeRouter setup for Swiss FTTH providers
I've had two EdgeRouter types connected to different Swiss FTTH ISPs and I was recently asked to share my experience. I still consider myself very much a beginner in managing these devices so feel free...
View ArticleIs something wrong with my Cron/VPN check script?
Hi I have a bit of a randomly dodgy DSL line. It behaves itself mostly, but, it can randomly (very recently twice per day) drop the VPN and not come back. I never got DPD working and instead I used...
View ArticleAnother Plex thread, Edge Router X v 1.8.0 -- port forwarding. (Solved, user...
Config dump below, login section redacted for reasons. When testing if the ports are opened, all of em fail. Can't figure out why, am networking nub. CLI instructions appreciated, I'm less comfortable...
View Articleipv6 dhcpv6-pd no-dns
Under what circumstances would I need to use no-dns when using SET commands?: For example when Iset interfaces ethernet eth0 dhcpv6-pd 'no-dns' or if I leave no-dns out like set interfaces ethernet...
View ArticleDual WAN Failover with OpenVPN Client
I've got an ERPOE-5 with dual WAN setup in failover mode working perfectly... it's been working without hitch for years, but now I want to tunnel network traffic through a VPN and I can't seem to get...
View ArticleEdgeRouter PoE - Multiple WAN IPs Port Forwarding v1.9
Hey Gang, I have been running this OS as a nubie for about a year. I have learned a lot but cant seem to bust through this one. I have multiple static WAN ip addresses. I want to split traffic INCOMING...
View ArticleSite-To-Site VPN not running on one end (both ERL with highly similar configs)
This is a bit frustrating. I had this briefly working and went to switch to using Dynamic DNS names instead of IP addresses, it took the tunnel down (expected) and never came back up (not expected). In...
View ArticleEdgeRouter with Avaya H.323 VPN remote phones
I have an Avaya 5610SW Remote VPN H.323 IP phone that I have not been able to get working with a new EdgeRouter PoE 5 in a home office. The EdgeRouter is quite a step up from the consumer router we had...
View ArticleERL v1.9.0 Slow WAN
on a 300/60 mbit connection i can max out the bandwidth on a speed test with v1.8.5 however after upgrading to v1.9.0 i only get half of this. I have had to restore the original configuration as it's a...
View ArticleIPSEC v1.9.0 wont come up
Ok so I previously had an issue with v1.8.5 where I couldn't connect L2TP/IPSEC so I was hoping the 1.9.0 would fix this. Which it did, however now straight IPSEC tunnels do not work. You can see my...
View ArticleZone based firewall with IPSEC
If you are doing a zone based firewall, is there a way to capture ipsec traffic in a zone? Unlike OpenVPN there is no interface to apply the rules to. I found that internet-local will catch ipsec...
View ArticleTools for firewall log analysis?
New ER-X user here. I was kind of bummed to see that there isn't any web representation of drops/rejects when you log them. Before I start thinking about a remote syslog host + something like...
View ArticleER-X - 1.9.0 throughput peaks at 40MB/s
I have an ER-X in a home environment. My network is laid out as follows: eth0 - waneth1~4 - switched lan if I host an iperf3 server on the lan and use the built in bandwidth tool to test it, I get...
View ArticleERL: Slow Internet
I'm having issues with slow internet speeds on my ERL. I'm on a 100x6 cable line. If I connect directly to the cable modem, I can get around 90-110 down, constantly 6 up. Once I have the cable modem...
View Article