Config dump below, login section redacted for reasons.
When testing if the ports are opened, all of em fail. Can't figure out why, am networking nub.
CLI instructions appreciated, I'm less comfortable with GUI. CLI leaves no room to mess up.
firewall {
all-ping enable
broadcast-ping disable
ipv6-receive-redirects disable
ipv6-src-route disable
ip-src-route disable
log-martians enable
name WAN_IN {
default-action drop
description "WAN to internal"
rule 10 {
action accept
description "Allow established/related"
state {
established enable
related enable
}
}
rule 20 {
action drop
description "Drop invalid state"
state {
invalid enable
}
}
}
name WAN_LOCAL {
default-action drop
description "WAN to router"
rule 10 {
action accept
description "Allow established/related"
state {
established enable
related enable
}
}
rule 20 {
action drop
description "Drop invalid state"
state {
invalid enable
}
}
}
receive-redirects disable
send-redirects enable
source-validation disable
syn-cookies enable
}
interfaces {
ethernet eth0 {
address dhcp
description Internet
dhcp-options {
default-route update
default-route-distance 210
name-server no-update
}
duplex auto
firewall {
in {
name WAN_IN
}
local {
name WAN_LOCAL
}
}
speed auto
}
ethernet eth1 {
description Local
duplex auto
speed auto
}
ethernet eth2 {
description Local
duplex auto
speed auto
}
ethernet eth3 {
description Local
duplex auto
speed auto
}
ethernet eth4 {
description Local
duplex auto
speed auto
}
loopback lo {
}
switch switch0 {
address 192.168.1.1/24
description Local
mtu 1500
switch-port {
interface eth1
interface eth2
interface eth3
interface eth4
}
}
}
load-balance {
}
port-forward {
auto-firewall enable
hairpin-nat enable
lan-interface switch0
rule 1 {
description HFS
forward-to {
address 192.168.1.136
port 8123
}
original-port 8123
protocol tcp_udp
}
rule 2 {
description Starcraft
forward-to {
address 192.168.1.136
port 6112
}
original-port 6112
protocol tcp_udp
}
rule 3 {
description Plex
forward-to {
address 192.168.1.136
port 32400
}
original-port 32400
protocol tcp_udp
}
wan-interface eth0
}
service {
dhcp-server {
disabled false
hostfile-update disable
shared-network-name LAN {
authoritative disable
subnet 192.168.1.0/24 {
default-router 192.168.1.1
dns-server 192.168.1.1
lease 86400
start 192.168.1.38 {
stop 192.168.1.243
}
}
}
}
dns {
forwarding {
cache-size 150
listen-on switch0
name-server 8.8.8.8
name-server 4.2.2.1
}
}
gui {
https-port 8443
}
nat {
rule 5010 {
outbound-interface eth0
type masquerade
}
}
ssh {
port 8022
protocol-version v2
}
telnet {
listen-address 192.168.1.1
port 23
}
}
system {
host-name ubnt
name-server 127.0.0.1
ntp {
server 0.ubnt.pool.ntp.org {
}
server 1.ubnt.pool.ntp.org {
}
server 2.ubnt.pool.ntp.org {
}
server 3.ubnt.pool.ntp.org {
}
}
syslog {
global {
facility all {
level notice
}
facility protocols {
level debug
}
}
}
time-zone UTC
}
traffic-control {
advanced-queue {
branch {
}
root {
}
}
}
zone-policy {
}
/* Warning: Do not remove the following line. */
/* === vyatta-config-version: "config-management@1:conntrack@1:cron@1:dhcp-relay@1:dhcp-server@4:firewall@5:ipsec@5:nat@3:qos@1:quagga@2:system@4:ubnt-pptp@1:ubnt-util@1:vrrp@1:webgui@1:webproxy@1:zone-policy@1" === */
/* Release version: v1.8.0.4853089.160219.1607 */