EdgeRouter and PS4 Network
I've had a problem the last five days with connecting to the Playstation Network through my EdgeRouter X SFP. It had worked up to then. I get an error on my PS4 (No. WS-37393-9), which Playstation says...
View ArticleStatic routes don't work properly
I am on the latest 1.9.0 on an ERL3.It would appear static routes do not work correctly. Case: We have a 2nd internal router that is used for VPN.EdgeRouter: 192.168.2.2 with a /24 behind it.The VPN...
View Articleset service dhcp-server use-dnsmasq enable doesn't show leases in UI
I'm new to the Ubiquiti world, and I was trying to get local dns going. It just so happens 1.9.0 was released! I tried to 'set service dhcp-server use-dnsmasq enable', but I am then unable to view...
View Article1.9 dnsmasq for DHCP
Hi, Having upgraded to 1.9 on my ER-X I enabled dnsmasq for DHCP. I have three VLANs (switch0.10, 0.20 and 0.30). I found that I only obtained DHCP leases on 0.10. I have dns forwarding listen-on...
View ArticleClik here to view.
Seeking max burst with priority options
Hello! Reading through the manual, having some difficulty understanding queuing. Also I'm getting about 60% bandwidth (so HW acceleration disabled?) I've attached a network diagram. I want both...
View ArticleEncounter Big Issue With Edge Max Router X
Hey all! This morning after I had finished my poridge with honey Put the oats in a saucepan, pour in the milk or water and sprinkle in a pinch of salt. Bring to the boil and simmer for 4-5 minutes,...
View Articleipv6 tunnel Hurricane Electric intermittent
I have a IPv6 tunnel connection with Hurricane Electric, connected via a EdgeRouter Lite. My ISP connection is a PPPOE fiber optic link limited to 750Kbps/up and 2000Kbps/down. For the past several...
View ArticleOpenVPN Client works on 1.8.5 but has issues since upgrade to 1.9.0 ?
we deployed 1.9.0 on our network successfully on each router but on the uplink we have problems with openvpn client. without changing settings, reverting back to 1.8.5 the openvpn client works...
View Article1.9.0 broke dashboard for me (using Firefox)
Hi I've just updated an Edgerouter Lite from the latest 1.9.0 beta to 1.9.0 and the dashboard is broken on Firefox 48.0. Screenshot attached. Previous versions including the latest beta worked without...
View ArticleIPSEC Site to Site with FQDN doesn't work in 1.9
Have confirmed that IPSEC site to site only works with ip address as peer vs FQDN. This is between 2 edgerouters with 1.9. If I switch from FQDN to IP address in config, VPN comes up fine. revert...
View Articlepppoe default route issue - route incomplete
In various LB scenarios with pppoe involved there's a need to tear down the pppoe default route. I've observed this in 1.8.5 and 1.9.0 (not sure about earlier releases)admin@router-brano:~$ show ip...
View ArticleBasic Setup vs. WAN +2LAN
I see there is now a basic setup in the wizard setup. I have only been using my ER for a few weeks now. Since I am weekend IT warrior, SOHO user, is it worth me "starting over" with the basic setup...
View ArticleEdgeRouter Lite Monitoring rx tx
I currenly have a EdgeRouter Lite. For some reason the RX and TX alogn with the port interface dont reflect properly. Currenly haveETH 0 InternetETH 1 BlankETH 2 to SwitchI have vlans 1-6 on eth2 So...
View ArticleERLite-3 Forwarding port 8443 on router but only to certain subnet
Im trying to access the web admin page from outside my network on port 8443. Web Admin port 8443 already works inside the network fine. I want to limit access to the web admin page to the subnet of my...
View ArticleER-X - initial setup - Stateful Firewall settings not necessarily recommended
Folks,Recently got an ER-X for home use to tighten up my home network, I really am displeased with the current consumer routers and the ER-X purchase was driven by a review by Steve Gibson of Security...
View ArticleDHCP-Server "groups" on a single subnet/vlan?
Can't think of a better way to title my issue; I have a single /24 for a small office, and due to a desire to avoid unnecessarily complicating things, I prefer to keep all the access ports on a single...
View ArticleOSPF equal cost now working/setup right
We connected our first redundant backhaul and while OSPF is advertising the secondary route to the rest of the network, it doesn't seem to pass any traffic with the cost set equal on all routes. The...
View ArticleIPSec Site-to-Site not working after upgrading to FW 1.9
After upgrading to FW 1.9 on my EdgeRouter Lite, the Site-to-Site VPN won't come up. Tried to downgrade back to 1.85 - but I'm still unable to get the VPN up and running. I tried deleting the VPN and...
View ArticleIPv6 for Guest network.
I've gotten IPv6 to work on my private network to work but couldn't do so on my Guest network. Both of them have IPv6 address assigned to them when I type in 'show interfaces'. I've used the same...
View ArticleClik here to view.
Load Balancing Problems
Hello ! My name is Anthony i work in small enterprise in France.I'm the network technician, since 1 week i install a ubiquiti edge router POE in load balancing. i use two internet network who are...
View Article