Dnsmasq for DHCP on 1.9.0
Does anyone know if the DHCP leases are writen to the internal usb stick when using dnsmasq for DHCP or are they just kept in in memory?I want to minimize write cycles to the internal usb stick as much...
View ArticleWhen downloading Higher CPU usage after firmware upgrade to 1.9.0
After upgrading firmware from 1.8.5 to 1.9.0 i see a higher CPU uasge when "hammering" the internet connection.With hammering i mean 11 thread newsgroup download. Standard singel downloads that reach...
View ArticleNew basic Setup wizard
As i have a ISp that uses VLAN 6 for Internet i decided to Factory reset my ER-X and start over because i can :-) That been said it does not connect after filling in all the blanks. Main difference i...
View Article1.9 IPSec VTI + OSPF drops flow every few minutes. VPN stays up but no packets.
Lasts for about about on average 2 minutes then it's back up for baout 1 - 3 minutes. There's gotta be some time or combo of timers in here somewhere that's killing me. I beefed up the OSPF times to 30...
View ArticleLink-local address being used by dns forwarder
Hi all, I am running v1.8.5 on an EdgeRouter Lite. I have configured a conditional forwarder to use a DNS server on the other end of my ipsec site to site VPN. set service dns forwarding options...
View ArticleIPv6 without messing up config
I just upgraded to 1.9.0 on my ERL3, I found the IPv6 wizard and I look forward to trying it out. However, is it possible to just run the IPv6 wizard without messing up the config I have on my LAN and...
View ArticleClik here to view.
How to view connections in web gui?
Hey everyone, I'm hoping this will be a quickly answered and I'm just being blind... So, the traffic analysis in the gui is cool...being able to see each local system and what type of traffic their...
View ArticleBFD interval & minrx
RFC-5880 describes Bidirectional Forwarding Detection (BFD). I just read it to try an understand the BFD features supported by EdgeMax routers. (Learned a lot...) I was able to map most of the EdgeMax...
View Article1WAN+3LAN no bridge, cannot get packets modified by WAN in firewall shaped by...
ERPro-8 with EdgeMax v1.8.5 I'd post config, but not at work right now. I have 3 LANS with the same shaping requirements, and 1 WAN(eth1) at 50/5mbps through a cable modem. The problem I'm trying to...
View ArticleIs the Edgemax or Unifi affected by this new Linux TCP hole ?
http://www.zdnet.com/article/linux-tcp-flaw-lets-anyone-hijack-internet-traffic/
View ArticleClik here to view.
Help with SNMP Monitoring OIDs for ERLite
Does anybody have a list of OIDs I can use to monitor my EdgeOS with NetXMS? Currently have only a handful configured, thanks
View ArticleSlow-down on EdgeRouter Pro with 1.8.5 and 1.9.0
I ran 1.70 for a LONG time. Stable and fast. I upgraded to 1.80, and still just fine. The EdgeRouter Pro is connected to the standard issue AT&T Uverse router, which is acting fine. My Internet...
View ArticleDual wan Voip issues of jitter and max thruput 150mbps 1.8.5 all the way back...
Voip issues of jitter and max thruput 150mbps 1.8.5 all the way back to 1.7 maybe priordual wan with fail over only, on aside note does take 30sec to a minture for failover to workat 150mbps thruput...
View Articlertsp helper
from 1.8.x the kernel module of the rtsp helper is available.but why not make all these ip helpers available and have an option to disable / enable if needed?as now many people spend numerous of hours...
View ArticleClik here to view.
EdgeMax 1.9 - Config Tree bug?
When I open system/package/repository and try to view the three subnodes (squeeze, wheezy and wheezy-security) in order via the ">". I first click one node the node's attributes is shown to the...
View ArticleER-PoE5 USB-Storage failure
Hey Guys, i use ER-PoE5 on the most of my sites. 3 weeks ago, a ER was rebooted due to power failure. After power was back ER did not start. With the console-port we saw that SQUASHFS was not able to...
View Articlepre-configuring rules
https://github.com/didenko/er_poe_fw im looking at the above guide as a template for my rules. lets say i wish to apply this configuration: switch switch0 { description DMZ firewall { in { name DMZ_IN...
View ArticleEdge Router X version 1.9 IPsec offloading speed test
HardwareSite A: Juniper SSG320 ( 100Mbps FTTH )Site B: Edge Router X ( 1Gbps GPON )VPN: Site to site, VTI, Encryption AES128 SHA1,with protocol BGPCPU Usage:below 30% when using 3DESabout 30% when...
View ArticleUpgrade to 1.9 failed on edgerouter X
Hi, i just updated my edgerouter X from 1.7 to 1.9 through the GUI but now my router is not coming back online. it looks like it is only doing switching now (as i can reach other devices on different...
View ArticleERX 1.9.0: ntp.conf syntax errors
A fresh replacement ERX, first configured with 1.7.1, then updated to 1.9.0. Looks like ntp.conf is not updated/handled properly. Jan 1 00:00:44 erx ntpd[936]: ntpd 4.2.6p2@1.2194-o Fri Jul 29 23:29:52...
View Article