Suggestion re:router
I recently purchased an ES48 switch and the EdgeMax router. Does it make more sense to DHCP on the switch or the router and could you please tell me why it makes more sense to run the DHCP server on...
View Articleconfiguration for 2wan + 2 or 1 LAN
I have one ISP who gives me up to five DYNAMIC ip addresses. I currently have one webserver and one PC behind the router. They are in the same LAN. Currently they have the same external (WAN) ip...
View ArticleStatic route issues
Hi, currently have a number of ERL-3 connected to a Draytek VDSL modem. The Draytek is in bridge mode so therefore passes the public IP address over pppoe0, configured Edgerouter using one of the...
View ArticleOpenVPN client connection super slow (1.5mbit/s!)- ER POE
So I have an Edgerouter POE and have some traffic routed through an OpenVPN connection (using ExpressVPN service). I have read lots of posts about this, and know that the ER isn't particularly fast...
View ArticleSet BGP community list
Hi, I'm trying to convert the following I would normally set on a Brocade router to EdgeOS: route-map ISP-ipv4-out permit 5match tag 666match ip address prefix-list advertiseset community...
View ArticleUnifi Edgerouter Lite Static IP setup
Hello, My ISP gave me these details IP Address: 106.51.64.7Subnet Mask: 255.255.224.0 Gateway: 106.51.64.1 DNS 1: 202.83.21.12DNS 2: 202.83.20.101 but when I enter this IP address in the config of my...
View ArticleEncrypt DDNS passwords in config.boot?
In config.boot, user login passwords are encrypted. Dynamic DNS passwords are not encrypted but are rather in plain text in config.boot. Could they be encrypted too?
View ArticleMultiple ports in firewall rule
I am trying to make a firewall builder spreadsheet which converts flow information to ACL rules.But I'm having a problem when it comes to setting port allocations.For the current process to work I need...
View ArticleClik here to view.
SSHD log level changed between 1.8.0 and 1.8.5
The log-level for messages from sshd into auth.log has changed between 1.8.0 and 1.8.5 in /etc/rsyslog.conf: until 1.8.0 (included) # Log authorization failure messages auth,authpriv.*...
View ArticleHelp with IPSec VPN Setup
Can someone look at my config file and see why I can't connect to my VPN? I'm trying to use my MacBook and iPhone to connect to my home network. eth1 is my primary LAN. I have an AT&T MicroCell...
View ArticleER-X v1.8.5, DHCP expiration time incorrect
Hi, In GUI set time zone to Japan UTC+9 Then in GUI -> DHCP View Leases, the Client Expiration time is incorrect, still using UTC time. i.e. Currect local time (UTC+9) is 2016-06-20, 6:05am, DHCP...
View ArticleMoving From IPv4 to IPv6
So, I have some experience In working with IPv4 and I find it realitvely easy to learn and get it setup, vlans and all. But It has its limitations when it comes to NAT. So Since IPv6 does not have that...
View ArticleEdgeRouter Lite DHCP Server For Multiple Subnets
Hello everyone! I just picked up an EdgeRouter Lite and installed the 1.8.0 firmware on it. I also have a Cisco 4948 connected to the EdgeRouter Lite on eth2. On the Cisco 4848 I have a total of three...
View Article1.8.5 availability
I see the post about 1.8.5 being released, but it's not on the download page. Is this an official release?https://www.ubnt.com/download/edgemax/edgerouter-x
View Articleiptables frontend or wizard?
I'm trying to use an EdgeRouter POE to replace an existing iptables firewall. I really like the hardware but am having lots of problems with the interface. Is there a way to prevent the OS from...
View ArticleER 8 Bridge Configuration / Switch
Hi, guys,, Im new to this kind of stuff, but recently both a edge max router 8 for my home having 4 accesspoint for 4 rooms. Just install the router in a wan2-2lan and set up as bridge to 1. My...
View ArticleClik here to view.
EdgeMAX config. Need help!
Hi guys!I first encountered ubnt.Please help.This is my first design of a network architecture.Tell me, will it work? Is there a design error?Prompt, please, that I'd better read that to configure it?...
View ArticleRouting issue
I am struggling slightly with a set up I am trying to achieve. I have a EdgeRouter lite andI am trying to set it up for the following configuration.Network 1 connected on Eth0(192.168.1.1) with an IP...
View ArticleRouting between eth0 and eth0.32 VLAN is not working
Hi, I want to put my Voice and SAT>IP services into a VLAN for Quality of Service Reasons. Therefore I've created a tagged VLAN 32 in my switches. My core LAN network is 10.0.0.0/12My VLAN-32...
View ArticleWhat is the CLI to change the default DPI engine data recycling window?
In the traffic analysis feature summary here https://help.ubnt.com/hc/en-us/articles/204951104-EdgeMAX-Deep-Packet-Inspection-Engine-for-EdgeRouter there is the statement "By default, the DPI engine...
View Article