Edgerouter Lite - 10/100 on WAN instead of 1000
I have been using an ERL/Unifi setup for about 6 months with minimal issues until recently. I pay for 1000 Mbps from my ISP but I've only been able to get around 80 Mbps on the fast.com speed test. I...
View Articlev1.9.0 DHCP not working
Just rebooted and DHCP is nort working on eth1 and eth2 interfaces. Not sure if this is a firewall issue or regular config issue. Any assistance greatly appreciated. firewall { all-ping enable...
View ArticleCan't access internet when connected through another router (ER-Pro8)
I have an ethernet connection in my building (witth a private IP address 192.168.1.x), and I wanted to use my ER8Pro to create my own private network that is not accessible by others in the building....
View ArticleNewbie home user Edgerouter Lite setup help
I was able to update the firmware on my Edgerouter Lite and using the wizard setup selected wan-2LAN2. eth0 is now the WAN port which is connected to my Netgear wireless router. I use Comcast as my ISP...
View ArticleEdgerouter OpenVPN
I've created a new internal VLAN which I want to share via a VPN Server (OpenVPN). I think that I have to create a bridge with the VLAN to make this. Is somewhere a easy guide on how to acomplish that?
View ArticleSimple QoS configuration problem
Folks, I'm trying to limit the upload for a single host on my network. Any thoughts on how to achieve that on EdgeRouter PoE (1.9.0)? Here's what is going on: since my upload bandwidth is really tight,...
View ArticleHow To Completely Isolate An IPSec VPN From Other Subnets?
Hey All, I've got a configuration that feels bleedingly close to what is actually needed save this one issue. I've crawled similar postings to no end but can't quite get there, so any help is much...
View ArticleEdgerouter X, firware 1.9.0 "Router kernel: [WAN_LOCAL-21-A]IN=eth0"
Hi All, I am a happy consumer now of a Edgerouter X. I am pretty new in this area.Recently I see the following messages in the log monitor appear twice every hour: Router kernel:...
View ArticlePort Forward behind ADSL Router
I have an Edgerouter X that, because the client has copper ADSL into the premises, needs to have a Huawei router in the mix. Unfortunately I can't just bridge the router as he has VOIP dependant on...
View ArticleTime to update the guts of the ERL?
It has been out for almost 4 years now, and really is underpowered for the new fq_codel support introduced in 1.7 (ERL only gets 60M throughput, the cheaper ERX gets 100M). In these 4 years, I would...
View ArticleEdge Router X as Layer 3 Switch
Hello all, Wondering if it is possible to setup a EdgeRouter X as a Layer 3 switch? I see documentation on resetting the unit and configuring as a Layer 2 switch and have completed this but would...
View ArticleEdge Router Lite - DMZ, "Type1" PS4 Connection
Hello everyone, Very new to Unifi and this advanced network gear. Currently I am running an Edge Router Lite and a UAP-AC-Lite in my home. My Setup is as follows:WAN+2LAN2 ISP Modem into eth0 as WAN...
View ArticlePrivate Internet Access OpenVPN Issues
I followed the other posts relative to setting up PIA's OpenVPN, and for the life of me, I cannot get my tunnel to connect and assign an IP. Is there any pertinent log information that will pinpoint...
View ArticleCannot connect to eth0
Just purchased an ER8 along with a crossover and straight cable. Configured my laptop ethernet IPv4 with 192.168.1.2 however on connecting the cable I do not get any link lights, and the ethernet...
View ArticleClik here to view.
Questions about ER-X-SFP
Hi All,I´m thinking about setting up a simple network with a ER-X-SFP and two UNIFI-AP-AC-LITE, so here are my questions: 1) will I be able to have both APs on the same lan-segment (Vlan 1 or whatever)...
View Articlesecond MAC address to a network interface
Hello,It is a possible to add second MAC address to a network interface ( example eth0/wan) or create virtual network interfaces with separate mac addresses ?In regular linux or especially openwrt we...
View ArticleEdgeMAX - IPv6 Tunnel
Hello. I bought EdgeMAX router and using in Japan. Some of Japanese ISP uses DS-Lite, it uses ipip6 tunnel. Current vyos support ipip6 tunnel, but EdgeOS v1.9.0 doesn't imprement it. I hope it will be...
View ArticleNewbie on Edgerouter Poe - need advice on minimum firewall setup for home use
Hi all,Have just done the initial setup using the wizard on 1.9. The Lan/wlan setup is fairly simple with 3 wired AP's and the usual amount of wired and wireless streaming devices / PCs and a WHS 2011...
View ArticleClik here to view.
Dynamic DNS problem edge router lite - afraid freeDNS
Hi All, I have configure the DDNS setting in the edge router lite and was working but later I found that it is not updating... Not sure if I have misconfigure, and hope to receive advise from here.....
View ArticleNew ER-X crashing with basic configuration
Hello, I recently bought an EdgeRouter X and upgraded it to 1.9.0. Unfortunately, the router keeps crashing about once or twice a day with a fairly basic config. The configuration is based on the...
View Article