Sustained uploads drop internet connection
Has anyone heard of this before? By drop, I mean I have to power cycle before being able to connect again. I've isolated the problem down to my EdgeRouter X router by ensuring that straight to the...
View ArticlePolicy routing to a DHCP/VPN dynamically assigned gateway
So I have a setup where I need to do policy routing from one subnet, however the destination gatway is dynamically assigned, in once case the default gateway from the wan interface which is assigned by...
View ArticleHairpin Nat v1.9 not playing nice with Verizon MiFi
I have a Novatel T1114 / Verizon MiFi modem/router ahead of my Edgerouter Lite. Hairpin NAT is needed for the NVR surveillance system. When polling CanYouSeeMe.org port X, it tests fine using the...
View ArticleSIP ALG Disabled
I have disabled SIP ALG, but when i run a test to see if SIP Alg is actually disabled it shows that it is still enabled. test i used, is a java applet:http://dc.nextiva.com/sipalg/ can someone else...
View ArticleERPoe-5 48v mode? UAP-IW Powering
I haven't been able to find the answer but hopefully its an easy one. I have a ERPoe-5 and want to power a UAP-IW (in wall) which is a 48v power. I ready the IW can only accept Mode A, but can't find...
View ArticleEdgeRouter X v1.9 VLAN enabled switch blocking VLAN traffic
Hi all, I am trying to use the new v1.9 VLAN switch feature. I have a pretty basic configuration I am trying to test and it's not working as expected. Here is the config: interfaces { ethernet eth0 {...
View ArticleHow do I enable VPN Passthrough in Edge OS
I'm not able to establish a VPN PPTP connection from any host in the network. When I bypass the EdgeRouter everything works fine. I also tried with an old Netgear Firewall and it worked as well.I have...
View ArticleERPro-8 ports
Is there a recommended port usage for the ERPro-8? I read some past threads saying the ASICs is on 2-4, etc but wasn't sure for which device it was. I'm currently using ETH0 for management of the ER,...
View ArticleVPN and related settings not in config.boot in backup?
I'm setting up an L2TP server on my ERL on 1.9. I get it all setup, get it tested, works fine. I can route packets, etc, all of it.So, I take a backup.The backup doesn't reflect my current...
View ArticleTwo Networks, One Router (192.168.1.0 and 192.168.10.0)
Two networks: 192.168.1.0/24 and 192.168.10.0/24. Call them .1 and .10. Dot 1 is *not* in a VLAN.Dot 10 is associated with VLAN 10. The problem is I cannot get traffice between 1. and .10 (and...
View Articleallow icmp with firewall policy
Hi!I am new to the edgerouter, previously i only worked with fortinet products but i am quite pleased with the ERAnyhow, could somebody tell me how i allow ping in a firewall policy?i.e how to allow...
View ArticleRouting with pseudo-ethernet
Hi, I have been configuring a router so as to load balance between : eth0 (dhcp), eth1(dhcp) and peth0 (fixed IP). The idea is to have peth0 linked to eth2, and add a 4G modem to the LAN, only on...
View ArticleERX-SFP stops responding during heavy uploads
I have 100/100 WAN connection and I can easily reach 90 mbps on uploads. I have noticed that ERX-SFP stops responding for a while and loses PPPoE connection during the times of heavy uploads and can...
View ArticleER-X, ERLite-3: option to disable port LED lights?
re Edgerouter X or Edgerouter Lite is it possible with either model to completely disable all LEDs, including the indicators on the ethernet ports? I found some old threads where this was asked before...
View ArticleWhere can I learn firewall basics
I just got done adding VLANs to my network in preparation for a huge jump into home automation. My main goal is to isolate my Guest and DMZ VLANs from my secure native network. I have been searching...
View ArticleClik here to view.
Thinking of replacing a TP-LINK VNP-600 with EdgeRouter lite.
Can I setup this router via GUI or do I need to learn CLICurrent Config for IPSEC VPN that I would need to configure.IKE PolicyPolicy Name:XXX-CISCOExchange Mode: Main AggressiveAuthentication...
View ArticleHow to disable Port Forward rules
Disapointing that we cant disable Port Forward rules like firewall rules. I wounder why ...
View ArticleAdmin Access on Each Subnet
Hey all. I have been coming through google and the U/I on the Edge router, I was curious. How can I restirct the U/I access to one IP. I have four subnets right now, each one of course has a GW, on...
View ArticleER8 - 2 vlan 2 dhcp
Hi, I want to create two vlan on my local network with two dhcp in order to create a network for two different departement. I create one vlan et one dhcp. I tag a port on my edgeswitch to test the...
View ArticleClik here to view.
Lost Dashboard info, Traffic Analysis Results, and other Issues
So I had the router testing Multi-Wan for a whole 12+hrs, then cam back to find no info in dashboard and traffic analysis.Dashboard Interfaces state they are all connected, even when the only thing...
View Article