No Connectivity to ERPOE-5 After Reboot
Greetings. I recently purchased an ERPOE-5 router. I had a power blip the other day which caused all networking gear to restart. The router powered back on but all connectivity was lost and I couldn't...
View ArticleNeed solution for Site to Site VPN
I am considering UBNT line for a site to site VPN project. The devices we have looked at are Cisco RV320 but they only allow CLASS C limited range /24 addressing. Our existing project is utilizing a...
View ArticleHow to separate LANs in GUI
Hello, I'm looking at replacing our current router with an EdgeRouter X to gain more routing features. My question I am trying to answer by looking through the user guide is: Can I configure the...
View ArticleuRPF funcionality
I'm sure there is a simple answer to this, but i am not finding it. Is uRPF supported on the EdgeRouter Pro, and if so, where do I find it? Thanks in advance.
View ArticleClik here to view.
iPhone IKEv2 VPN Config [ER 1.9.0; iOS 10]
This post is to show the basic settings I needed to get this working. I am not including certificate creation or firewall setup. I use zone-policy anyway and most of the examples around here don't....
View Articleigmp proxy crashes - script to check and restart automatically
It seems like every Sunday when I wake up to watch football I have no picture. I ssh into the router and type restart igmp-proxy, it warns me that igmp-proxy is not currently running, and I'm good for...
View ArticleERL and VPN on Secondary LAN in WAN+2LAN2
Hello everyone! I've been lurking for a long time and at the recommendation of a co-worker, I purchased an ERL. Its on version 1.9.0. I currently have it set it WAN+2LAN2 mode, Port 1 is WAN, Port 2 is...
View ArticleIPSec Site 2 Site with Snapgear.
Hey everyone, I was wondering, im attempting to config a VPN tunnel between my EdgeRouter Pro via the web interface which i have done my research and it seems like i have te config and ip's pointed to...
View ArticleForcing OpenDNS results in a reverse engineering challenge
Greetings, a few days ago I found some DNS-related commands on the internet, I plugged them into my ERL and got exactly the results I wanted. These commands forced all DNS traffic to the opendns...
View ArticleAuto Provisioning Polycom Phones via DHCP Option 160 with EdgeMax/EdgeRouter
Need to automatically provision your Polycom phones against Endpoint Manager in FreePBX, or another config source with a Ubiquiti EdgeRouter? Simply add this to your DHCP configuration and substitute...
View ArticleChromecast in a routed network
For anyone interested, I made a short description of the absolute minimum configuration to get devices to reach a Chromecast in a routed environment. http://www.cron.dk/edgerouter-and-chromecast/ Best...
View ArticleLoad Balancing with different down/up speeds
I've just bought an ER-LITE for my office. I currently have two Internet connections from different providers.WAN1 is 2Mbps up and 2Mbps downWAN2 is 2Mbps up and 8Mbps downI have set up load balancing...
View ArticleWiring 8 rooms in house in single LAN, what do I need?
I'd like to wire 8 rooms in a home with GigE, all on a single LAN. From what I've read so far, this means I'd have to bridge all the ports on an EdgeRouter and also on an EdgeSwitch. These will be used...
View ArticleHelp with Firewall
I'd like to set up my EdgeRouter's firewall to block all incoming connections except on the ports that I have forwarded. I find the firewall settings very confusing. I'm used to ufw on Linux, which...
View ArticleVLAN, trunk port and IPTV
Hey, I just replaced my ASUS router to a ER POE and struggling to configure my ER for my setup of devices used with the ASUS. Physical setup ER:ISP(100/100)->eth0eth2 -> Unifi AP AC-LReth3->...
View ArticleSFP and VPN Questions
Good afternoon everyone, I am setting up a Edgerouter SFP and a Edge Switch 24 and I have a couple of questions. 1) I wanted to connect the two devices using the SFP ports. When I plug the SFP in, the...
View ArticleER-X limit bandwidth by interface
We have a sitution were we need to split a WAN connection to 3 routers. To do this we configured a ER-X to be a layer 2 switch. Now we would like to limit the bandwidth available to each router through...
View ArticleEdgeRouter X v1.9.0 load-balancing issue
Hi Guys I have quite big problem with load balancing.I have two ISP, HSDPA+ 3/6 mbps (monthly 30GB) and satelite link 10/2 mbps (monthly 16GB), both link are very stable and reliable only disadvantage...
View ArticleIPSEC Traffic and Firewall
Working on setting up an ERL lite with a site to site VPN. The setup of IPSEC actually looks pretty straight forward. Following this guide here...
View ArticleEdgeMAX: OpenVPN Site-to-Site
hello guys i already configure my two sites vpn ipsec. site A side is dynamic and Side B is static. from site A (dynmic) i can ping the local tunnel interface , but not computer in the LANFrom site B (...
View Article