OSPF hello packet mismatch
Hi, I am getting OSPF hello packet mismatch. Please check my OSPF config:# show interfaces ethernet eth5 vif 11 ip ospf authentication { md5 { key-id 1 { md5-key 55e492f5a2812ebf } } } cost 10...
View ArticleERX SFP Switch?
This should be a simple question but I can't find a definitive answer. Does the ERX SFP have a hardware switch on any of its ports? I found a post from when it was released where said yes, but there...
View ArticleCustom SSH Configuration
Is it possible to customise the SSH configuration ? Specifically im looking to customise the Key Exchange, Cipher, and HMAC algorithms to ensure only strong alorithms are used. From the CLI i can...
View ArticleNo Internet for Guest Network
Hello, I'm VERY new to networking so I apologize for any silly or obvious questions here. I have the Edge Router Lite which works fantastic for what I wanted it for. It was configured with the help of...
View ArticleEdgeRouter Lite - Dual WAN - One Subnet - Forcing Traffic Out Specific Ports
Hello, I am not sure if this specifc problem has been addressed because it is very specific. I have two ISP connections, one configured on eth0 and one on eth1. I have one subnet on the LAN side, and...
View Articlesome traffic not traversing ipsec site to site with unifi AP adoption.
I have two edgerouters with an ipsec tunnel between them. Traffic passes fine between sites for systems etc. I have a unifi controller at site 1, with a single AP at site 2. 2 AP at site one work to...
View ArticleDoes a factory reset wipe everything?
Can anyone tell me, If an EdgeRouter has been compromised and malicious software has been installed on it, Will performing a factory reset wipe the entire unit , including any malicious software that...
View ArticleIPSEC VPN Site-to-Site
I have been racking my brain on trying to get this tunnel working. I keep getting this in the cliubnt@ubnt# show vpn ipsec status Specified configuration path is not validHere are my configs for both...
View ArticleEdgeRouter Lite and VoIp (8x8) Strange Issue
We are experiencing strange behavior with our VoIP phones, and I was hoping someone might be able to offer some suggestions. DISCLAIMER: my networking knowledge is very limited. We have approximately...
View ArticleCan't get ER8 router to talk to ES48 switch using VLANs
Here are the configs. I currently have a patch cord from Eth1 on the ER8 to port 0/47 of the switch. Thanks in advance! Port 1 of the switch is connected to a pre-existing Cisco network and I am...
View ArticleClik here to view.
DHCPv6 custom parameters?
The DHCPv4 implementation provides "global-parameters" and "shared-network-parameters" options, making it possible to manually specify options that aren't exposed through options in the CLI, for...
View ArticleOpenVPN tunnel keeps restarting
I have two ERX SFPs connected via OpenVPN tunnel. Like clockwork, every couple minutes they break the connection and restart it. I gather it's from my keepalive 10 60 directive, but I don't know why...
View ArticleDynamic qos
Is there any way to create some sort of dynamic qos? For example: Only 1 client using the connection:Allowed 100% upload and downloadno restrictions on network 2 or more clients:Each client may only...
View ArticleConnTrack still taking down routers....
I configured an EdgeRouter 8 to replace an old Imagestream for a small ISP. We have two OSPF interfaces via wireless backhauls, a LAN, and a WISP AP facing interface with around 100 customers hanging...
View ArticleEdgeMAX Beginner's Guide - PPTP Setup - Command Line - Video Tutorial
https://www.youtube.com/watch?v=_sI6XF6gSGM This video will walk you through setting up the PPTP VPN service on your EdgeRouter through the command line. The standard GUI (non config tree) VPN button...
View ArticleBandwidth management solution
Hi guys, just looking for bandwidth management solution here. How do you guys managed to control the internet usage of clients. Any suggestion ? Sorry for my english...
View ArticleTraffic analysis Category
What is meant by "apps". I do not understand what IatTraffic Analysis - can enter add Category.
View ArticleER PoE 5 Dual PPPoE WAN Failover
Having read a number of articles and posts about dual WAN load balancing and failover where the scenario always seems to be 1x PPPoE WAN & 1x DHCP WAN, I'm struggling to find the correct setup for...
View ArticleAdditional VPN gateway
Hello, I have ER-L with 350 mbp/s failover dual wan. The problem is that some of the websites are blocked by ISP. ISP blocks websites by IP.I have tryed setting up VPN client on ER-L but it caused...
View ArticleMaintain access to AP configuration page when Load-Balancing disables a WAN...
Hello, I'm using an ER-X on a boat with two Bullets connected to load balance and failover between multiple relatively unreliable wifi connections. It is working fine except that when a wifi...
View Article