BT Internet IPv6 but not external IPv6 address
I see that BT have confirmed that IPv6 is now available to all BT Internet customers. http://www.ispreview.co.uk/index.php/2016/11/bt-broadband-lines-now-support-ipv6-internet-addresses.html I’m trying...
View ArticleClik here to view.
EdgeRouter Pro BGP configuration
Hello guys, Our network is currently running Quagga. We have 2 BGP peers - one main, which receives full route tables and one as backup, which receives default route only. The main one has a couple of...
View Articlehairpin nat?
cant access device at port 8080 from LAN (by name) but can from WAN (by name)but i can access device at port 80 from LAN and WAN by nameHairpin NAT enabled.firewall, auto offfirewall config. default...
View Articlecan edgerouter max do this?
two machines on LAN, both on port 80.machine1: www.xyz.commachine2: www.otherurl.com can the edge router max direct traffic to the correct machine from WAN to LAN?
View ArticleBug? Setting RDNSS on interface clears radvd prefix setting
I noticed that radvd was advertising an upstream DNS server instead of my local caching server, so I went into the configuration and set the apporpriate ipv6 DNS addresses. All seemed well until my...
View ArticleClik here to view.
SSL handling with Reverse Proxy on Edgerouter POE
Hi again, Been here before and learned a lot. Now I have a new issue that I hope that you will be able to help with me.I have added this drawing to make sense of what I wish for. We only have one...
View ArticleHow to block traffic in/out to a specific device
Hi all, I was able from previous help block a given port. I followed the same logic in trying to set up a block for a specific device, or group of devices. I mapped all our devices, from phones,...
View ArticleClik here to view.
Firewall Secure?
Hello, I just bought an ERPOE-5 and I'm new to Ubiquiti products. I'm having a bit of trouble grasping the way the firewall works in UBNT. But after fiddling for a while, this is my current ruleset:...
View ArticleEdgeRouter PoE Max AP Support?
Just wondering if anyone is running multiple AC access points via the EdgeRouter PoE ports? I want to run one UAP-AC and two UAP-AC-PRO and based on the published max wattages it should be possible....
View ArticleRouting newbie, see if I have this sorted out
Hi All, Long, long time IT guy here that knows next to nothing about routing. I recently decided that I wanted to step up my network game at the house. Replaced an old Asus router and gbit switch for...
View ArticlePolycom VOIP phone won't register - ER-8 Edgerouter 1.90
Very plain setup. Using known good Level 3 line, separate switch, and known good phone that registers fine on existing setup. Ran load balancing config, setup DHCP, did not enable firewall, disabled...
View ArticleCannot connect to L2TP over IPSec from macOS or iOS clients
Hi all, I recently upgraded a number of OS X and iOS 9 devices on my network to macOS and iOS 10, which removed the support for PPTP. This was fine as I'd intended to move away from PPTP shortly...
View Article4G/3G Connection options on Edgerouter X
Since the Edgerouter X only has ethernet ports, I'm looking for a low cost solution to provide a 3G/4G connection via ethernet. I know Sierra makes a 3G/4G gateway along with Cradlepoint but the price...
View ArticleEdgeRouter Lite Dropping Internet Connetion
Hi - I have seen a couple of posts about similar symptons. I just bought an EdgeRouter Lite - running 1.9. I have ETH0 connected to the WAN, ETH1 connected to a switch where everything hangs off. I...
View ArticleL2TP remote access not passing traffic with dual WAN
I had this working before I added the second internet connection but now I can't get it to pass traffic. I'm using the windows native VPN client. It connects fine and when I do 'show VPN...
View ArticleS16 SNMP OID's
Hi, I’m looking for the SNMP OID’s for POE config on the S16. Specifically the ones that would let you disable/enable passive24v. I tried an snmpwalk, but without a MIB (if there is one available i'm...
View ArticleHelp with VLAN
Hi,We're having issues with the Guest PortalRouter: Edgemax LiteSwitch: NETGEAR FS728TP, Toughswitch 5 port, Linksys unmanaged switchAP: 3x UAP-LR & 1...
View ArticleEdgeRouter Lite v1.9.0 - port forward port 80 to internal webserver
I have done an extensive search within the community and on Google related to this issue: For...
View ArticleClik here to view.
Help Destination-base Routing.
I am new to Ubiquitiy, how can i configure destination based routing? I have 2 ISPs, i dont want to use load balance, I just want Spotify and Iflix use the 2nd ISP.
View ArticleEdgeRouter X SFP 500 Mbps Max Throughput
I recently had Comcast Xfinity Gigabit installed. They advertise a 940Mbps/35Mbps connection. They are currently rolling out the service, and provide a Technicolor DOCSIS 3.1 modem, and a Netgear...
View Article