Which special character is not allowed for password?
Hi..I'm using password generator for all my password.When I'm using this password Password: 8!#&5eU@923U3.7Ds%~21oDa8)Y"8. OpenDNS is not updating. I'm pretty sure It's not from the OpenDNS,...
View ArticleClik here to view.
New ER X replaced old router & DHCP server, different default gateway IP...
Some backgroundI just received my EdgeRouter X. I updated to EdgeMAX v1.9.0 immediately, and then set up the ER X to be my new router using the Basic Setup wizard that turns eth0 into the WAN port, and...
View ArticleIPSEC Tunnel Up, but no traffic
I'm trying to configure a site-to-site vpn on v1.8.5. I can see the tunnel is up and I can even see packets getting from one site to the other, but ping, web, remote desktop connections dont work. One...
View ArticleUpgrade from ERL to Edgerouter pro
After upgrading, everything is working but just a question about those additional ports, just create them on CLI and further nothing?
View ArticleQuestion: Migrating configuration from ER-PoE to ER-X?
I have, in service, an EdgeRouter PoE5 running v1.4.1, which I can't update the OS on without factory-resetting it because of a mistake I made attempting to remediate shellshock. I also have, not yet...
View ArticleCan't Access Webmail using load balance
How can i setup load balance. we have multple IP from both ISP. how can i set it up so every time a access the webmale or a bank website. it will only use the WAN 1 (ISP 1)
View ArticleHelp choosing equipment for CenturyLink gigabit installation
Disclaimer: My experience with networking gear is reserved to consumer router+APs.I'm getting centurylink gigabit install at our new house and want to use a Netgear Orbi (or similar wireless AP setup)...
View ArticleBasic Queue & Youtube
EdgeRouter PoE 5-Portv1.9.0Thought I would try and throttle Youtube traffic using basic queue functionality.If I apply the queue without the application category it seems to throttle accordingly, if I...
View ArticleClik here to view.
static host-mapping stopped working edge router x
I have a simple setup where my Edge router X is connected to an AP, a linux box and sometimes I connect internet through eth0 and sometimes i remove the cable for a variety of reasons. Besides that, it...
View ArticleER-X SSH can't change port
I recently noticed error where I look access to SSH via a custom port and later find it is listening on 22. When trying to change SSH port (shows correct in config), the unit returns this error...sh:...
View ArticleHow to open ports?
Hello,I just installed my edgerouter lite and configured with a how to I found on the internet for replacing my french ISP orange.This worked fine but throught the web interface, I can't open ports.No...
View ArticleClik here to view.
Use PPTP client for all traffic
Hi everyone, I configured a PPTP outbound interface (so my Edge dials out to a provider). I tried to add the 0.0.0.0/0 static interface-route, to send all the traffic over the pptpc interface.....
View ArticleSetup Problems
Hi!As im on my way to replacing my fortigate with an ERLi got some problems which im looking to solveFirst problem ) I would like a default deny all policy which applies to all interfaces --> how do...
View ArticleCan't connect my new EdgeRouter PoE to Internet
Got my router a couple of days ago. A the same time I got a fiber connection to Internet (on ADSL now). The router was shipped with 1.2 firmware so the first thing I did was to upgrade to 1.9 to get...
View ArticleDesign a network
Hello there.We are about to start a hosting company, but since we are not network peoples, we need some help.We could use help to design our network. what we need help to:VLANsIP addressesconfig of...
View ArticleError enabling Smart Queue
I'm unable to enable Smart Queue on my ERL running 1.9.0. I've tried via the WebUI, and receive a very vague error, "Failed to apply the configuration". When I try via the CLI, I get this:...
View ArticleAccess port
Is there any way I could be able to set up eth2 as an access port? I got eth1 as trunk with vlans 10,20,30,40 and i want eth2 to be kn vlan40 as well.
View ArticleIPv6 and Local Local Addresses
I have a working IPv6 setup where all DNS is done via IPv6. I'd like to setup IPv6 DNS such that my EdgeRouter Lite is the primary DNS and forwards requests. There are 2 problems with this: 1) Using...
View ArticleClik here to view.
EdgeRouter X VLANs must be numbered to route?
Hi All, I've been loving the ER-X:https://community.ubnt.com/t5/EdgeMAX/ER-X-platform-thank-you/m-p/1649939#M123800 Question though. Two questions actualy: 1) Am I handeling VLANs correctly on the...
View ArticleSmart Queue - limit LAN bandwidth?
I have just finished migration from an ER-5-POE in my tower cabinet to an ER-PRO in the main comms room, and have a doubt about the Smart Queue feature. I have an underground ToughCable running to a...
View Article